The Toyota Prius, recognized for its gasoline effectivity and eco-friendly popularity, is a well-liked alternative amongst drivers searching for a dependable and environmentally acutely aware car. One widespread upkeep activity that Prius house owners could encounter is changing or eradicating the antenna base. Whereas it might appear to be a frightening activity, eradicating the Prius antenna base is comparatively simple with the right instruments and some easy steps. Whether or not you are upgrading to a brand new antenna or just must make repairs, this complete information will offer you detailed directions on the way to safely and effectively take away the Prius antenna base out of your 2013 mannequin.
Earlier than embarking on this activity, it is important to collect the required instruments and security gear. You will want a Phillips head screwdriver, a flathead screwdriver, a plastic pry instrument or a spudger, and gloves to guard your fingers. Moreover, make sure you park your Prius in a protected and well-lit space to reduce distractions and enhance visibility. After you have your instruments and security gear prepared, you’ll be able to proceed with the elimination course of by following the step-by-step information outlined beneath.
To start, find the antenna base on the roof of your 2013 Prius. It’s usually located close to the middle of the roof and surrounded by a black plastic cowl. Utilizing the flathead screwdriver, gently pry open the plastic cowl by inserting the tip of the screwdriver into the small hole between the duvet and the roof. As soon as the duvet is unfastened, you’ll be able to take away it utterly by hand. Subsequent, use the Phillips head screwdriver to loosen the screws that safe the antenna base to the roof. As soon as the screws are eliminated, you’ll be able to rigorously pull the antenna base straight up and off the roof. Be sure you deal with the antenna base with care to keep away from damaging it or the encompassing elements.
Find the Antenna Base
The antenna base in your 2013 Prius is situated on the roof of the car, in the direction of the rear. To seek out it, observe these steps:
- Stand behind the car and lookup on the roof.
- Find the black plastic base that’s connected to the roof with a single bolt.
- That is the antenna base.
Here is a extra detailed description of every step:
- Stand behind the car and lookup on the roof. This offers you a transparent view of the highest of the car.
- Find the black plastic base that’s connected to the roof with a single bolt. The bottom is round and about 2 inches in diameter. It’s situated in the direction of the rear of the roof, close to the middle.
- That is the antenna base. After you have discovered the bottom, you’ll be able to proceed to the subsequent step to take away it.
| Step | Description |
|---|---|
| 1 | Stand behind the car and lookup on the roof. |
| 2 | Find the black plastic base that’s connected to the roof with a single bolt. |
| 3 | That is the antenna base. |
Take away the Inside Trim Panel
To take away the inside trim panel across the base of the antenna, observe these detailed steps:
Step 1: Find the Trim Panel
Determine the trim panel surrounding the antenna base on the headliner. It’s often an oblong or round panel product of plastic or material.
Step 2: Detach the Trim Panel
Gently use a pry instrument or a flat-head screwdriver wrapped in a material to rigorously pry the trim panel unfastened from the headliner. Insert the instrument into the hole across the fringe of the panel and apply light strain to launch the clips holding it in place. Work across the perimeter of the panel, detaching the clips separately.
Step 3: Take away the Trim Panel
As soon as all of the clips are launched, rigorously carry the trim panel away from the headliner. Disconnect any wiring or cables connected to the panel, equivalent to these for the antenna or roof mild (if relevant). Place the trim panel in a protected location to forestall harm.
Detach the Antenna Base
1. Insert a flat-head screwdriver or a trim elimination instrument into the small slot on the base of the antenna. Gently pry the antenna base unfastened from the roof of the car.
2. As soon as the antenna base is unfastened, take away it from the car and set it apart.
Detach the Antenna Cable
1. Find the antenna cable that’s connected to the bottom of the antenna. The cable might be held in place by a small plastic clip or screw.
2. If the cable is held in place by a clip, use a flat-head screwdriver or a trim elimination instrument to pry the clip open and launch the cable.
3. If the cable is held in place by a screw, use a screwdriver to take away the screw and launch the cable.
| Antenna Cable Connector | Elimination Technique |
|---|---|
| Plastic Clip | Pry open the clip with a flat-head screwdriver or a trim elimination instrument. |
| Screw | Take away the screw with a screwdriver. |
4. As soon as the antenna cable is launched, rigorously pull the cable via the opening within the roof of the car.
5. Disconnect the antenna cable from the antenna base by urgent on the discharge button on the connector and pulling the 2 connectors aside.
Unscrew the Antenna Base Bolts
Now, let’s sort out the true activity: eradicating the antenna base. You will want a 10mm socket wrench or a deep socket set for this step.
-
First, find the 4 bolts holding the antenna base to the roof. They need to be organized in a sq. sample.
-
Take your socket wrench and thoroughly insert it into the primary bolt. Flip it counterclockwise to loosen it.
-
Repeat this course of for the remaining three bolts.
-
As soon as all 4 bolts are unfastened, you’ll be able to take away the antenna base by gently lifting it straight up.
Now that you’ve got the antenna base eliminated, you’ll be able to transfer on to disconnecting the antenna wire. Bear in mind to deal with the antenna with care to keep away from any harm.
Further Ideas for Unscrewing the Bolts
Listed here are some useful tricks to make unscrewing the bolts simpler and extra environment friendly:
| Tip | Description |
|---|---|
| Use a Deep Socket | A deep socket will present higher entry to the bolts beneath the antenna base. |
| Apply Stress | Apply regular strain to the wrench whereas turning it. Utilizing extreme power might harm the bolts. |
| Use a Penetrating Oil | If the bolts are rusted or corroded, apply a penetrating oil across the threads to loosen them. |
Take away the Antenna Base
Step 1: Take away the Heart Console
Start by eradicating the middle console by unscrewing the bolts that maintain it in place. As soon as the bolts are eliminated, carry the console upwards to disconnect it from the car’s electrical system.
Step 2: Find the Antenna Connector
Beneath the middle console, you will see the antenna connector. It’s usually situated close to the firewall and linked to a wiring harness.
Step 3: Disconnect the Antenna Wire
Disconnect the antenna wire from the connector by urgent on the discharge button or tab. Observe that the placement and form of the discharge mechanism could fluctuate relying on the precise mannequin yr.
Step 4: Unscrew the Antenna Base
Find the antenna base, which is linked to the antenna wire and mounted on the roof of the car. Utilizing an appropriate instrument equivalent to a wrench or socket, unscrew the antenna base and thoroughly take away it from the roof.
Step 5: Clear and Reinstall the Antenna Base
Earlier than reinstalling the antenna base, it is vital to scrub each the bottom and the mounting floor on the roof. It will guarantee optimum sealing and stop moisture ingress. Apply a skinny layer of sealant or adhesive to the bottom of the antenna earlier than screwing it again into place. Tighten the bolts securely, guaranteeing a comfortable and watertight connection.
| Instruments Required | Security Precautions |
|---|---|
| Phillips head screwdriver | Put on gloves to keep away from cuts |
| Wrench or socket | Disconnect the battery earlier than engaged on electrical elements |
| Sealant or adhesive | Park on a secure and degree floor |
Clear the Contact Factors
After eradicating the antenna base, you’ll need to scrub the contact factors the place it connected to the car’s roof. Dust and corrosion can construct up over time, inflicting issues with the antenna’s sign reception. To wash the contact factors, use a cotton swab dipped in rubbing alcohol or a specialised contact cleaner. Gently rub the swab over the factors till they’re freed from filth and particles. As soon as the contact factors are clear, permit them to dry utterly earlier than reattaching the antenna base.
| Supplies required |
|---|
|
Further suggestions for cleansing the contact factors:
- Watch out to not use an excessive amount of power when cleansing the contact factors, as this might harm them.
- If the contact factors are closely corroded, you could want to make use of a fine-grit sandpaper to take away the corrosion. Be sure you clear the contact factors completely with rubbing alcohol after sanding.
- As soon as the contact factors are clear, apply a small quantity of dielectric grease to them to assist forestall future corrosion.
Reinstall the Antenna Base
As soon as the previous antenna base is eliminated, you’ll be able to proceed to put in the brand new one. Comply with these steps:
-
Align the brand new antenna base with the mounting holes on the roof.
-
Place the washers onto the bolts.
-
Tighten the bolts utilizing the torque wrench to the desired torque setting.
-
Set up the antenna by screwing it onto the antenna base.
-
Join the antenna wire to the antenna base.
-
Safe the antenna wire with the offered zip tie or electrical tape.
-
Take a look at the antenna by turning on the radio and checking for a transparent sign.
| 12 months | Bolt Measurement | Torque (Nm) |
|---|---|---|
| 2013-2018 | M6 | 12-15 |
Safe the Antenna Cable
As soon as the antenna base is eliminated, you will must safe the antenna cable. Here is the way to do it:
Find the Antenna Cable
Determine the antenna cable, which is often a black or grey wire that runs from the antenna base to the again of the automotive.
Disconnect the Antenna Cable
Gently pull the antenna cable straight out of the antenna base. Don’t twist or bend the cable.
Wrap the Antenna Cable
Use electrical tape or a zipper tie to wrap the disconnected antenna cable. It will forestall it from dangling or getting broken.
Route the Antenna Cable
Fastidiously route the wrapped antenna cable alongside the present wiring harness or any designated channels within the automotive’s inside.
Safe the Antenna Cable
Use cable clips or zip ties to safe the antenna cable to the automotive’s body or inside panels. It will hold it in place and stop it from shifting round.
Reconnect the Antenna Cable
Find the antenna port on the again of the automotive’s radio or audio system. Align the antenna cable with the port and gently push it in till it clicks into place.
Tighten the Antenna Cable
Hand-tighten the antenna cable by turning it clockwise. Don’t overtighten the cable, as this might harm the port or the cable.
Reattach the Inside Trim Panel
9. Reattach the Inside Trim Panel:
| Step | Directions |
|---|---|
| a. | Find the plastic clips across the perimeter of the trim panel. |
| b. | Align the clips with the corresponding slots on the inside panel. |
| c. | Apply strain to the trim panel across the edges to reconnect the clips. |
| d. | Ensure the trim panel is securely mounted and would not rattle. |
| e. | Tighten the screws within the decrease corners of the trim panel to additional safe it. |
| f. | Fastidiously pull on the trim panel to make sure it’s securely connected. |
| g. | If crucial, alter the clips or screws till the trim panel suits snugly. |
| h. | Change the A-pillar trim cowl by snapping it again into place. |
| i. | Verify that every one the trim panels, screws, and clips are correctly secured. |
Bear in mind to deal with the trim panels with care to keep away from harm. In case you encounter any difficulties, seek the advice of with a professional mechanic.
Take a look at the Antenna
Earlier than you begin eradicating the antenna base, it is vital to check the antenna to verify it isn’t working correctly. Here is the way to do it:
- Flip in your automotive radio.
- Tune to a radio station that you recognize has a powerful sign.
- In case you hear static or interference, it implies that your antenna will not be working correctly.
- In case you do not hear any static or interference, it implies that your antenna is working correctly and you’ll proceed to eradicating the antenna base.
Listed here are some extra suggestions for testing your antenna:
- If in case you have a multimeter, you need to use it to check the continuity of the antenna wire.
- You can even attempt connecting a distinct antenna to your automotive radio to see if it really works.
- In case you’re nonetheless having hassle, you’ll be able to take your automotive to a mechanic to have them diagnose the issue.
How To Take away Prius Antenna Base 2013
To take away the Prius antenna base in a 2013 mannequin, observe these steps:
1.
Find the antenna base on the roof of the car.
2.
Utilizing a Phillips head screwdriver, take away the 2 screws that safe the antenna base to the roof.
3.
Gently pull up on the antenna base to take away it from the roof.
4.
Disconnect the antenna wire from the antenna base.
5.
Take away the antenna base from the car.
Individuals Additionally Ask About How To Take away Prius Antenna Base 2013
How do you take away the shark fin antenna on a Prius?
To take away the shark fin antenna on a Prius, observe these steps:
- Find the shark fin antenna on the roof of the car.
- Utilizing a Phillips head screwdriver, take away the 2 screws that safe the antenna to the roof.
- Gently pull up on the antenna to take away it from the roof.
- Disconnect the antenna wire from the antenna base.
- Take away the antenna from the car.
How do you take away the roof rack on a Prius?
To take away the roof rack on a Prius, observe these steps:
- Find the 4 bolts that safe the roof rack to the roof of the car.
- Utilizing a wrench, take away the 4 bolts.
- Gently carry the roof rack off of the roof of the car.
- Take away the roof rack from the car.
How do you take away the antenna on a Prius?
To take away the antenna on a Prius, observe these steps:
- Find the antenna on the roof of the car.
- Utilizing a Phillips head screwdriver, take away the screw that secures the antenna to the roof.
- Gently pull up on the antenna to take away it from the roof.
- Take away the antenna from the car.
