“`html
Eliminating a defective drain pump on an LG mannequin WT1101CW washer could be a daunting process, however it’s essential for conserving your equipment operating easily. The drain pump is chargeable for expelling water from the washer through the spin cycle, so a malfunctioning pump can result in water accumulation and unsightly odors. Thankfully, changing the drain pump is a comparatively easy course of that may be completed with the precise instruments and a bit technical know-how. On this complete information, we’ll stroll you thru the step-by-step means of eradicating the drain pump out of your LG mannequin WT1101CW washer.
Earlier than embarking on the restore, collect the mandatory instruments and supplies. You will have a Phillips head screwdriver, a flathead screwdriver, a pair of pliers, and a brand new drain pump appropriate together with your washer mannequin. To forestall water harm through the course of, place towels or a shallow pan beneath the washer to catch any leaks. Moreover, unplug the washer from the facility outlet for security causes.
To entry the drain pump, start by eradicating the again panel of the washer. Find the screws securing the panel in place and take away them utilizing the Phillips head screwdriver. As soon as the panel is free, rigorously raise it off and set it apart. The drain pump is usually located on the backside of the washer, linked to the drain hose. Disconnect the drain hose by loosening the clamp with pliers. Subsequent, find {the electrical} connector connected to the drain pump and unplug it by urgent on the discharge tab. Lastly, use the flathead screwdriver to pry the drain pump free from its housing.
“`
Figuring out and Finding the Drain Pump
Figuring out and finding the drain pump in your LG mannequin WT1101CW washer is important for troubleshooting and performing repairs when essential. The drain pump is chargeable for expelling water from the washer through the rinse and spin cycles. It’s sometimes situated on the backside of the equipment, close to the rear.
To find the drain pump, comply with these steps:
– Unplug the washer from the facility outlet and switch off the water provide.
– Tilt the washer again barely to entry the underside.
– Search for the drain pump, which shall be a small, spherical element with wires and hoses connected to it.
– The drain pump is normally secured with screws or bolts. Take away these fasteners to detach the drain pump from the washer.
Instruments Required:
| Phillips screwdriver |
Unplugging the Washer and Water Provide
1. Flip off the water provide to the washer. That is normally finished by turning off the valves behind the washer. If you cannot discover the valves, you’ll be able to flip off the principle water provide to your private home.
2. Unplug the washer from {the electrical} outlet.
Tilting the Washer Again
1. Fastidiously tilt the washer again by greedy the edges of the washer and pulling it in direction of you. Watch out to not tip the washer over fully.
2. Place a block of wooden or a sturdy object beneath the entrance of the washer to maintain it from falling.
Eradicating the Drain Pump
1. Find the drain pump. It’s normally situated on the backside of the washer, behind the entrance panel.
2. Disconnect the wires from the drain pump. Watch out to not harm the wires.
3. Take away the screws that maintain the drain pump in place. There are normally two or three screws.
4. Fastidiously pull the drain pump out of the washer.
Changing the Drain Pump
1. Insert the brand new drain pump into the washer.
2. Safe the drain pump with the screws.
3. Join the wires to the drain pump.
4. Tilt the washer again down and take away the block of wooden.
5. Plug the washer again into {the electrical} outlet.
6. Activate the water provide to the washer.
Accessing the Drain Pump
To entry the drain pump on the LG mannequin WT1101CW, comply with these steps:
1. Unplug the washer from the facility outlet.
2. Flip off the water provide to the washer.
3. Disconnect the drain hose from the again of the washer.
4. Open the pump filter cowl. This cowl is normally situated on the backside of the entrance panel of the washer. To open the duvet, use a coin or screwdriver to show the duvet counterclockwise.
As soon as the duvet is open, you will notice the drain pump. The drain pump is a small, spherical system that’s linked to the drain hose. To take away the drain pump, first disconnect {the electrical} connector from the pump. Then, use a wrench to loosen the bolts that maintain the pump in place. As soon as the bolts are free, you’ll be able to take away the drain pump from the washer.
5. Take away the drain pump.
6. Clear the drain pump.
7. Reinstall the drain pump.
8. Join the drain hose to the again of the washer.
9. Activate the water provide to the washer.
10. Plug the washer into the facility outlet.
Disconnecting Electrical Wires
With the pump meeting faraway from the washer, you’ll be able to proceed with disconnecting {the electrical} wires.
1. Find {the electrical} connector on the pump. That is sometimes a white or grey plastic connector with a number of wires linked to it.
2. Pinch the discharge tabs on the connector and pull it straight as much as disconnect it from the pump.
3. Word the place of every wire on the connector so that you could reconnect them accurately later.
4. Use a pair of wire cutters to chop the wires near the connector.
5. Strip roughly 1/2 inch of insulation from the tip of every wire.
Detailed Rationalization of Wire Stripping:
Wire stripping is the method of eradicating the insulation from the tip of a wire to reveal the steel conductor. That is essential for connecting the wires to the brand new drain pump.
To strip wires, you have to a pair of wire strippers. Insert the wire into the suitable gap on the strippers and squeeze the handles to chop by means of the insulation. Watch out to not lower into the steel conductor.
As soon as the insulation is lower, pull it off the tip of the wire. If the insulation is tough to take away, you should utilize a pair of pliers to softly pull it off.
| Stripping Instrument | Dimension | Vary |
|---|---|---|
| Wire Strippers | 18-24 AWG | 0.05-0.25mm² |
| Pliers | 14-22 AWG | 2.1-0.32mm² |
| Utility Knife | All wire sizes | N/A |
Eradicating the Drain Pump Bracket
To take away the drain pump bracket, comply with these detailed steps:
- Find the 2 screws that safe the drain pump bracket to the washer’s base.
- Utilizing a screwdriver, rigorously unscrew each screws and take away them.
- Gently raise the drain pump bracket away from the washer.
- Disconnect the wire harness from the drain pump.
- Find the 2 bolts that safe the drain pump to the drain pump bracket.
- Utilizing a wrench or socket, rigorously unscrew the 2 bolts and take away them. Word that the drain pump might include a small quantity of water, so be ready to empty it when eradicating the bolts.
- Fastidiously take away the drain pump from the drain pump bracket.
- Examine the drain pump for any harm or blockages and substitute it if essential.
- Reassemble the drain pump and drain pump bracket by reversing the above steps.
Troubleshooting Drain Pump Bracket Elimination
| Drawback | Resolution |
|---|---|
| Screws are stripped or rusted | Use a screw extractor or penetrating oil to take away the broken screws. |
| Bolt threads are broken | Apply a thread locker or sealant to the bolts earlier than screwing them in. |
| Drain pump is caught | Gently faucet the drain pump with a mallet or hammer to loosen it. |
Detaching the Inlet and Outlet Hoses
To detach the inlet and outlet hoses:
- Find the drain hose and the inlet hose.
- Use pliers to loosen the hose clamp on the drain hose.
- Gently pull the drain hose off the drain pump.
- Repeat steps 2-3 for the inlet hose.
Eradicating the Drain Pump Filter
The drain pump filter is situated contained in the drain pump housing. To take away the filter:
- Find the drain pump filter cowl on the underside of the drain pump housing.
- Flip the drain pump filter cowl counterclockwise to loosen it.
- Pull the drain pump filter straight out.
- Clear the drain pump filter completely with water.
- Reinsert the drain pump filter into the drain pump housing.
- Flip the drain pump filter cowl clockwise to tighten it.
Reattaching the Inlet and Outlet Hoses
To reattach the inlet and outlet hoses:
- Push the drain hose onto the drain pump.
- Use pliers to tighten the hose clamp on the drain hose.
- Repeat steps 1-2 for the inlet hose.
| Step | Motion |
|---|---|
| 1 | Find the inlet and outlet hoses. |
| 2 | Use pliers to loosen the hose clamps on the hoses. |
| 3 | Gently pull the hoses off the drain pump. |
| 4 | Take away the drain pump filter and clear it completely. |
| 5 | Reinsert the drain pump filter into the drain pump housing. |
| 6 | Reattach the inlet and outlet hoses to the drain pump. |
| 7 | Use pliers to tighten the hose clamps on the hoses. |
Eradicating the Drain Pump
To entry and take away the drain pump on an LG mannequin WT1101CW washer, comply with these steps:
1. Unplug the washer and switch off the water provide.
Security first! All the time disconnect the facility and water to forestall electrical shock or water harm.
2. Open the entrance door of the washer.
It will reveal the internal workings of your washer.
3. Take away the 2 screws holding the entrance panel in place.
Find the screws on the highest corners of the entrance panel and unscrew them.
4. Tilt the entrance panel ahead.
Fastidiously raise the entrance panel and tilt it ahead to entry the parts behind it.
5. Find the drain pump.
The drain pump is usually situated on the backside of the washer, behind the entrance panel.
6. Disconnect {the electrical} connector.
Unplug {the electrical} connector connected to the drain pump.
7. Disconnect the drain hose.
Loosen the clamp securing the drain hose to the drain pump and disconnect the hose.
8. Take away the mounting screws.
Unscrew the screws holding the drain pump in place. Here is an in depth breakdown of the screws you will encounter:
| Screw Kind | Amount |
|---|---|
| Prime screws | 2 |
| Backside screws | 3 |
| Aspect screws | 2 |
As soon as all screws are eliminated, you’ll be able to gently pull the drain pump out of its housing.
Reinstalling the Drain Pump
1. Earlier than you begin, be sure to have all the mandatory instruments and elements, which can embody a brand new drain pump, a screwdriver (Phillips head), and a washer (comparable to a rubber washer). Typically it is also helpful to have a flashlight readily available as effectively.
2. Begin by unplugging the washer from the facility and shutting off the water provide. You need to now disconnect the drain hose.
3. Find the mounting screws for the outdated drain pump. These are normally situated on the underside of the entrance of the washer. Take away the screws and punctiliously pull out the outdated drain pump by disconnecting the facility to it.
4. Set up the brand new drain pump into the machine, join its energy, and put the mounting screws again in place.
5. Reinstall the drain hose. Be sure it is securely fixed, as a free drain hose could be a main supply of leaks.
6. Activate the water provide to the washer and plugin the machine. Run a brief wash cycle to check that the brand new drain pump is working correctly.
7. Test for any leaks across the drain pump or the drain hose.
8. If every thing is working correctly, put the entry panel again on the washer and also you’re all set! You’ve got simply efficiently changed the drain pump in your washer.
Troubleshooting
For those who’re having bother reinstalling the drain pump, the next ideas might assist:
Tightening the Mounting Screws
Be sure the mounting screws are tightened securely. If they are not tight sufficient, the drain pump is probably not correctly secured and will leak.
Checking the Drain Hose Connection
Be sure the drain hose is correctly linked to the drain pump. If the hose just isn’t linked accurately, it may leak.
Resetting the Washing Machine
For those who’re nonetheless having bother, attempt resetting the washer. This may be finished by unplugging the machine from the facility and ready 60 seconds earlier than plugging it again in and turning it on.
| Instrument | Description |
|---|---|
| Phillips head screwdriver | Used to take away the mounting screws for the drain pump |
| Rubber washer | Used to seal the connection between the drain pump and the washer |
| Flashlight | Used to see contained in the washer if wanted |
Find out how to Take away Drain Pump on LG Mannequin WT1101CW
LG’s mannequin WT1101CW is a popularly used top-load washer. Over time, it could be essential to take away the drain pump and clear it from any clogging or international objects. Here is a step-by-step information that will help you safely take away the drain pump from this LG washer:
-
Unplug the washer
Previous to beginning any restore work, ensure to unplug the washer from the facility supply. It will stop any electrical shock.
-
Flip off the water provide
Find the water provide valves behind the washer and shut them off to forestall water from flowing into the machine through the restore.
-
Tilt again the washer
Fastidiously tilt the washer again to entry the underside of the unit. It’s possible you’ll want to make use of a chunk of wooden or a small block to prop it up.
-
Find the drain pump
Take a look at the underside of the washer and establish the drain pump. It normally has a cylindrical physique with wires and a hose connected to it.
Take away the screws that maintain the pump in place. Unplug the wires linked to it and detach the hose linked on the prime of the drain pump.
-
Clear the drain pump
As soon as the drain pump is eliminated, examine the housing for any clogs or international objects. Take away any particles and examine the impeller for any harm. If essential, clear the impeller with a tender brush or a material.
-
Reattach the drain pump
Place the drain pump again into its housing and tighten the screws to safe it in place. Reattach the hose and wire connections. Be sure all connections are correctly fitted.
-
Take a look at the washer
Reconnect the facility provide and water provide to the washer. Run a brief cycle to make sure that the drain pump is correctly functioning.
Folks Additionally Ask
Find out how to clear LG WT1101CW Drain Pump?
Find the drain pump on the backside of the washer and disconnect it from the wires and hose. Examine it for any clogs or particles and clear it with a tender brush or a material. If the impeller is broken, it could should be changed.
The place to seek out the drain pump on LG WT1101CW?
The drain pump is situated on the backside of the LG WT1101CW washer. It has a cylindrical physique with wires linked to it.
How typically ought to the drain pump be cleaned?
The frequency of cleansing the drain pump is dependent upon the utilization of the washer. If it is used incessantly, cleansing it as soon as each six months or so is really helpful. Nevertheless, if the machine is used much less typically, cleansing it annually may suffice.
