Changing the battery on a Dell Perc 710 is a comparatively easy process that may be accomplished in a couple of minutes. Nevertheless, it is very important take precautions to keep away from damaging the controller or the battery. To finish, this process, it’s possible you’ll want a Phillips #0 screwdriver, a brand new battery, and an anti-static wrist strap. An anti-static wrist strap just isn’t required however it’s endorsed to keep away from damaging the controller resulting from electrostatic discharge.
Earlier than you start, energy down the server and unplug it from the ability outlet. As soon as the server is powered down, take away the entrance bezel of the server. Find the Perc 710 controller and take away the 2 screws that safe it to the chassis. As soon as the screws are eliminated, rigorously slide the controller out of the chassis. Find the battery on the controller and press down on the discharge tab. The battery will pop up and might be eliminated. Take the brand new battery and insert it into the controller. Press down on the battery till it clicks into place. Slide the controller again into the chassis and safe it with the 2 screws. Reinstall the entrance bezel of the server and plug it again into the ability outlet.
As soon as the server is powered on, the brand new battery will start charging. The battery sometimes takes about 24 hours to completely cost. As soon as the battery is absolutely charged, it can present energy to the controller within the occasion of an influence failure. You will need to substitute the battery each three to 5 years to make sure that the controller has a dependable energy supply.
Security Precautions
When changing the PERC 710 battery, it is very important take the next security precautions to keep away from potential hazards and guarantee a clean and profitable course of:
1. Energy Off and Unplug the System:
1.1 Energy Off the System: Earlier than making an attempt any {hardware} upkeep, all the time energy off the system correctly to forestall knowledge loss and {hardware} harm. To do that, comply with these steps:
- Click on on the “Begin” menu and choose “Shut Down”.
- Await the system to close down utterly earlier than continuing.
1.2 Unplug the Energy Wire: As soon as the system is powered off, unplug the ability wire from {the electrical} outlet to make sure that the system is totally de-energized.
2. Precautions to Keep away from Electrostatic Discharge (ESD):
ESD can harm delicate digital elements. To keep away from this, take the next precautions:
- Floor your self by touching a metallic floor or sporting an anti-static wrist strap earlier than dealing with the PERC 710 battery.
- Solely deal with the battery by its edges or connector to keep away from touching the uncovered digital elements.
- Work on an anti-static mat or in an ESD-protected space.
- Place the previous battery in an anti-static bag earlier than disposal.
3. Consult with the System Guide:
For particular directions and security precautions associated to your specific Dell server mannequin, consult with the system’s person handbook or technical documentation.
Gathering Vital Instruments
To efficiently substitute the Dell Perc 710 battery, you’ll require a couple of important instruments to make sure a protected and environment friendly course of.
The next desk summarizes the required instruments:
| Instrument |
|---|
| Anti-static wrist strap |
| Phillips #1 screwdriver |
| Tweezers (non-obligatory) |
Anti-static Wrist Strap:
An anti-static wrist strap is essential to forestall electrostatic discharge (ESD), which might harm delicate digital elements just like the Perc 710 battery. Put on the strap by attaching its metallic snap to a grounded floor and the elastic band to your wrist.
Phillips #1 Screwdriver:
A Phillips #1 screwdriver is crucial for eradicating and tightening the screws that safe the battery housing. Guarantee you might have a driver with a safe match and a pointy tip to keep away from damaging the screw heads.
Tweezers (Elective):
Tweezers might be useful for manipulating small elements, such because the battery connector, if needed. Nevertheless, if you’re uncomfortable utilizing tweezers, you should use your fingertips with warning.
Finding and Eradicating the Battery
The Perc 710 battery is positioned on the entrance of the cardboard, subsequent to the backplane connectors. To take away the battery, comply with these steps:
- Energy down the system and unplug it from the ability outlet.
- Find the Perc 710 card within the system.
- Unplug the battery from the Perc 710 card. The battery is a small, black cylinder with a white connector.
Changing the Battery
After you have eliminated the previous battery, you possibly can set up the brand new one. To do that, comply with these steps:
- Align the brand new battery with the connector on the Perc 710 card.
- Press down on the battery till it clicks into place.
- Plug the system again into the ability outlet and energy it on.
Verifying the Battery Set up
After you have changed the battery, it’s best to confirm that it’s put in appropriately. To do that, comply with these steps:
- Log into the Perc 710 internet interface.
- Click on on the “Configuration” tab.
- Click on on the “Battery” sub-tab.
The Battery Standing web page will show the standing of the battery. The battery must be listed as “OK” and the cost degree must be above 50%.
| Battery Standing | Description |
|---|---|
| OK | The battery is put in appropriately and is functioning correctly. |
| Warning | The battery is low on energy and must be changed. |
| Vital | The battery is critically low on energy and the system is not going to boot if the battery just isn’t changed. |
Inserting the New Battery
4. Insert the brand new battery:
-
Find the battery connector on the Perc 710 card. It is a small, black connector positioned close to the entrance of the cardboard.
-
Take away the previous battery by rigorously lifting it straight up from the connector. Don’t pry or power it.
-
Align the brand new battery with the connector and insert it rigorously. Be sure to push it down firmly till it clicks into place.
-
Confirm that the battery is securely seated by gently wiggling it backward and forward. If it strikes, repeat steps 3 and 4.
-
As soon as the battery is correctly put in, the Perc 710 card ought to mechanically detect and acknowledge it. If it would not, energy cycle the server to power a refresh.
Word: The next desk summarizes the steps for inserting the brand new battery:
| Step | Motion |
|---|---|
| 1 | Find the battery connector on the Perc 710 card. |
| 2 | Take away the previous battery by rigorously lifting it straight up from the connector. |
| 3 | Align the brand new battery with the connector and insert it rigorously. Push it down firmly till it clicks into place. |
| 4 | Confirm that the battery is securely seated by gently wiggling it backward and forward. If it strikes, repeat steps 3 and 4. |
| 5 | Energy cycle the server to power a refresh if the Perc 710 card would not mechanically detect the brand new battery. |
Connecting the Energy Cable
Comply with these steps to attach the ability cable:
- Make sure that the PERC 710 backplane is securely put in within the chassis.
- Find the ability cable that got here along with your PERC 710.
- Join one finish of the ability cable to the ability connector on the PERC 710 backplane.
- Join the opposite finish of the ability cable to an influence outlet.
- Detailed Steps for Connecting the Energy Cable:
Step Description 1 Establish the ability connector on the PERC 710 backplane. It’s positioned on the bottom-left nook of the backplane, subsequent to the battery. 2 Align the arrow on the ability cable with the corresponding arrow on the ability connector. 3 Firmly insert the ability cable into the connector till it clicks into place. 4 Safe the ability cable by tightening the retaining screw. - Confirm that the ability LED on the PERC 710 backplane is lit, indicating that energy is being provided to the controller.
Verifying the Alternative
As soon as the brand new battery is put in, it is essential to confirm if it is functioning appropriately. Comply with these detailed steps:
-
Restart the server: Flip off the server, wait a couple of seconds, after which energy it again on. This step will permit the server to acknowledge the brand new battery.
-
Log in to the system: Entry the server’s working system and log in as an administrator.
-
Test the BIOS settings: Enter the server’s BIOS settings and navigate to the “System Configuration” or “RAID Configuration” menu. Find the “Battery Standing” part and confirm if the battery is detected and its standing is “Optimum” or “OK.”
-
Run a diagnostic check: Most Dell servers have built-in diagnostic instruments that may check the battery’s well being. Consult with the server’s documentation for particular directions on operating the diagnostic check.
-
Monitor the occasion log: The server’s occasion log might comprise details about the battery’s standing. Test the log for any errors or warnings associated to the battery.
-
Observe the bodily indicator: Some Dell servers have a bodily indicator, equivalent to an LED gentle, that exhibits the battery’s standing. Make sure that the indicator is inexperienced or one other shade indicating a wholesome battery.
If any of those steps point out an issue with the brand new battery, contact Dell Technical Help for additional help.
| Step | Motion |
|---|---|
| 1 | Restart the server |
| 2 | Log in to the system |
| 3 | Test the BIOS settings |
| 4 | Run a diagnostic check |
| 5 | Monitor the occasion log |
| 6 | Observe the bodily indicator |
Changing the Cowl
As soon as the battery has been changed, it is very important substitute the quilt to guard the interior elements of the PERC 710 card. To switch the quilt, comply with these steps:
1. Connect the Battery Cowl
Align the battery cowl with the PERC 710 card and slide it into place till it clicks securely.
2. Safe the Battery Cowl (Elective)
Relying on the chassis, an non-obligatory screw can be utilized to safe the battery cowl in place. If accessible, find the screw gap on the battery cowl and tighten the screw to safe the quilt.
Superior Troubleshooting: Addressing Battery Cowl Errors
In some circumstances, after changing the battery, the PERC 710 card might show an error message indicating an issue with the battery cowl. To resolve this challenge, comply with these steps:
-
Test the Battery Cowl Connection: Make sure that the battery cowl is absolutely seated and securely hooked up to the PERC 710 card.
-
Clear the Battery Cowl Contacts: Examine the battery cowl contacts for any particles or corrosion. Gently clear the contacts with a tender fabric to take away any contaminants.
-
Reset the PERC 710 Card: If cleansing the contacts doesn’t resolve the difficulty, strive resetting the PERC 710 card. To do that, energy down the server, take away the PERC 710 card, after which reinsert it.
| Symptom | Trigger | Resolution |
|---|---|---|
| Battery Learn Error | Defective battery cowl connection | Test and safe the connection |
| Battery Cowl Not Detected | Soiled battery cowl contacts | Clear the contacts |
| Battery Cowl Tamper Error | Cowl has been opened | Reset the PERC 710 card |
Configuring the BIOS
To start out the method of changing the battery in your Dell Perc 710, you’ll need to configure the BIOS settings. Listed here are the steps to do that:
1. Energy on the server and press F2 to enter the BIOS Setup Utility.
2. Navigate to the “System Configuration” menu.
3. Choose “iDRAC Settings” and press Enter.
4. Choose “PERC Settings” and press Enter.
5. Choose “Battery Configuration” and press Enter.
6. Choose “Substitute Battery” and press Enter.
7. The system will now immediate you to substantiate that you simply wish to substitute the battery. Press “Y” to substantiate.
8. The system will now substitute the battery. This course of might take a number of minutes. As soon as the method is full, the system will show a message indicating that the battery has been changed efficiently. Press any key to proceed.
Here’s a desk summarizing the steps for configuring the BIOS:
| Step | Motion |
|---|---|
| 1 | Energy on the server and press F2 to enter the BIOS Setup Utility. |
| 2 | Navigate to the “System Configuration” menu. |
| 3 | Choose “iDRAC Settings” and press Enter. |
| 4 | Choose “PERC Settings” and press Enter. |
| 5 | Choose “Battery Configuration” and press Enter. |
| 6 | Choose “Substitute Battery” and press Enter. |
| 7 | Verify that you simply wish to substitute the battery. |
| 8 | The system will substitute the battery. |
How To Substitute Dell Perc 710 Battery
The PERC H710, PERC H810, and H710P mini cache battery is a small element that powers the cache on the RAID controller. If the battery fails, the cached knowledge will likely be misplaced, which might result in knowledge corruption or loss. You will need to substitute the battery frequently to forestall this from taking place.
Troubleshooting Battery Points
If you’re having issues along with your PERC H710, PERC H810, or H710P mini cache battery, there are some things you are able to do to troubleshoot the difficulty.
1. Test the LED
The PERC H710, PERC H810, and H710P mini cache battery has an LED that signifies the standing of the battery. If the LED is off, the battery just isn’t receiving energy. If the LED is blinking, the battery is nearing the top of its life and must be changed.
2. Test the occasion log
The PERC H710, PERC H810, and H710P mini cache battery will log occasions to the system occasion log. If the battery is failing, there will likely be an occasion logged within the occasion log.
3. Substitute the battery
You probably have decided that the battery is failing, you’ll need to exchange it. The battery is a small, coin-shaped battery that’s positioned on the RAID controller. To switch the battery, comply with these steps:
1. Energy down the server.
2. Take away the quilt from the server.
3. Find the RAID controller.
4. Take away the battery from the RAID controller.
5. Insert the brand new battery into the RAID controller.
6. Substitute the quilt on the server.
7. Energy on the server.
4. Replace the firmware
If you’re nonetheless having issues with the PERC H710, PERC H810, or H710P mini cache battery, it’s possible you’ll have to replace the firmware. The firmware is the software program that controls the operation of the RAID controller. Updating the firmware can repair bugs and enhance the efficiency of the RAID controller.
5. Contact Dell help
If you’re unable to resolve the difficulty your self, you possibly can contact Dell help for help. Dell help might help you troubleshoot the difficulty and give you a substitute battery if needed.
6. Battery Life
The PERC H710, PERC H810, and H710P mini cache battery has a lifespan of about 3 years. After 3 years, the battery will should be changed.
7. Battery Alternative Value
The price of a PERC H710, PERC H810, or H710P mini cache battery is about $100.
8. Battery Alternative Interval
The PERC H710, PERC H810, and H710P mini cache battery must be changed each 3 years.
9. Battery Capability
| Battery Mannequin | Capability (mAh) |
|---|---|
| CR2032 | 225 |
| CR2025 | 160 |
| CR2016 | 90 |
Instruments Required
• Phillips #2 screwdriver
• Anti-static wrist strap
Step-by-Step Directions
1. Security Precautions
• Disconnect the server from all energy sources.
• Floor your self by sporting an anti-static wrist strap.
2. Take away the Entrance Bezel
• Unclip the bezel from the highest and gently pull it ahead.
3. Take away the Battery Module
• Find the battery module on the high of the RAID controller card.
• Grasp the battery module firmly and pull it straight up.
4. Insert the New Battery
• Align the brand new battery with the slot on the controller card.
• Push the battery down into place.
5. Reinstall the Entrance Bezel
• Slide the entrance bezel again into place till it clicks.
6. Energy on the Server
• Reconnect the ability cables and restart the server.
Suggestions for Sustaining Battery Well being
• Hold the server in a cool, dry atmosphere.
• Keep away from exposing the battery to excessive temperatures.
• Don’t try to recharge the battery.
• Substitute the battery each 3-5 years or when the battery indicator gentle turns purple.
• If the battery fails, the RAID controller will lose its configuration knowledge. Guarantee that you’ve got common backups of your knowledge to forestall potential knowledge loss.
• Use a UPS (Uninterruptible Energy Provide) to guard the server from energy outages. This can forestall the battery from draining and inflicting knowledge loss.
• Monitor the battery standing frequently. The battery standing might be checked utilizing the Dell OpenManage Server Administrator (OMSA) utility.
• If the battery standing exhibits indicators of degradation, substitute the battery as quickly as doable to keep away from knowledge loss.
Tips on how to Substitute Dell Perc 710 Battery
The Dell Perc 710 battery is a small, replaceable battery that gives energy to the RAID controller. The battery is positioned on the entrance of the RAID controller and is straightforward to exchange. Listed here are the steps on find out how to substitute the Dell Perc 710 battery:
- Energy down the server and unplug it from the ability outlet.
- Open the server case and find the RAID controller.
- Press the discharge latch on the entrance of the RAID controller and slide the controller out of the chassis.
- Find the battery on the entrance of the RAID controller. The battery is a small, cylindrical battery with a black plastic cowl.
- Press the discharge tab on the battery and slide the battery out of the controller.
- Insert the brand new battery into the controller and slide it into place.
- Slide the RAID controller again into the chassis and shut the server case.
- Plug the server again into the ability outlet and energy it on.
Individuals Additionally Ask About Tips on how to Substitute Dell Perc 710 Battery
How typically ought to I substitute the Dell Perc 710 battery?
The Dell Perc 710 battery must be changed each three to 5 years.
What occurs if the Dell Perc 710 battery fails?
If the Dell Perc 710 battery fails, the RAID controller will lose energy and the info on the RAID array will likely be prone to being misplaced.
Can I substitute the Dell Perc 710 battery myself?
Sure, you possibly can substitute the Dell Perc 710 battery your self. The process is straightforward and solely requires a couple of fundamental instruments.
