Your kitchen faucet is likely one of the most-used fixtures in your house. As such, it is sensible to change into conversant in fundamental upkeep duties. Must you ever want to exchange your kitchen faucet, realizing easy methods to uninstall it is step one of the method. Whereas knowledgeable plumber can actually deal with this job for you, it’s additionally a reasonably simple DIY venture that may be accomplished in just a few easy steps. Preserve studying to learn to uninstall kitchen faucet in lower than an hour.
Earlier than starting, you will want to assemble just a few instruments. You will have a pair of adjustable pliers, a screwdriver, a bucket, and some rags. You may additionally need to placed on a pair of outdated garments or a smock since some water could spill throughout the removing course of. After getting your instruments and are prepared to start, step one is to show off the water provide to your kitchen faucet. You possibly can often discover the shut-off valves beneath the sink. As soon as the water is turned off, open the tap to launch any remaining water within the line.
Subsequent, you will want to disconnect the water provide traces. To do that, use the adjustable pliers to loosen the nuts that join the water traces to the tap. Watch out to not overtighten the nuts, as this might harm the traces. As soon as the nuts are free, you’ll be able to disconnect the water traces by hand. Now, you will want to take away the mounting nuts that maintain the tap in place. These nuts are often situated beneath the sink. Use the screwdriver to loosen the nuts, however there doubtless is not going to be sufficient clearance to take away them together with your fingers. As a substitute, grip the nuts with the adjustable pliers, and take away them the remainder of the best way. With the mounting nuts eliminated, now you can raise the tap up and out of the sink.
Gathering the Crucial Instruments
Uninstalling a kitchen faucet requires just a few important instruments to make sure a clean and environment friendly course of. Earlier than you start, collect the next objects:
- **Adjustable wrench:** A big, adjustable wrench is good for loosening and tightening the nuts that safe the tap to the sink and water provide traces.
- **Basin wrench:** This specialised wrench is designed to grip the mounting nuts on the underside of the sink, which are sometimes tough to achieve with an everyday wrench.
- **Phillips head screwdriver:** You could want a Phillips head screwdriver to take away the deal with screws on some faucet fashions.
- **Flat head screwdriver:** A flat head screwdriver can be utilized to pry open any cussed clamps or clips which may be holding the tap in place.
- **Pliers:** Pliers will be useful for gripping and loosening small nuts or screws which may be tough to achieve with different instruments.
- **Bucket:** A bucket is crucial for gathering water that will drain from the tap and water provide traces throughout the removing course of.
Extra Instruments for Particular Faucet Varieties
Relying on the kind of faucet you’ve got, you could want extra instruments. For instance:
| Faucet Sort | Extra Instruments |
|---|---|
| Pull-out faucet | Allen wrench or hex key |
| Touchless faucet | Electrical tape or wire nuts |
Disconnecting the Water Traces
As soon as the tap is disconnected from the sink, you’ll be able to proceed to disconnect the water traces. On this step, you will want a pair of adjustable wrenches or a basin wrench.
1. Flip off the water provide.
Earlier than beginning, make sure that the water provide to the tap is turned off. You possibly can often discover the shut-off valves beneath the sink or within the basement or crawlspace.
2. Detach the provision traces from the tap.
Find the provision traces related to the tap, one for decent water and one for chilly water. Use the adjustable wrench to loosen the nuts that safe the provision traces to the tap. As soon as loosened, you’ll be able to detach the provision traces by hand.
3. Drain any remaining water.
As soon as the provision traces are disconnected, there could also be some remaining water within the traces or faucet. To empty this water, open the tap and permit it to run till the water stops flowing. Alternatively, you need to use a moist/dry vacuum to suck out the water.
Loosening the Faucet Base
As soon as your water provide is turned off, you’ll be able to proceed to loosen the tap base. This may be finished utilizing a wrench or a pair of pliers.
-
Find the 2 nuts which can be holding the tap base in place. These nuts are often situated on the underside of the tap, simply above the baseplate.
-
Use a wrench or pliers to loosen the nuts. Watch out to not overtighten the nuts, as this will harm the tap.
-
As soon as the nuts are free, you need to be capable to take away the tap base by pulling it straight up.
-
If the tap base is caught, you’ll be able to strive utilizing a penetrating oil to loosen it up. Apply the oil to the nuts and let it sit for a couple of minutes earlier than attempting to loosen them once more.
| Instruments you will want: |
|---|
| – Adjustable wrench |
| – Penetrating oil (non-obligatory) |
| – Pliers (non-obligatory) |
Eradicating the Faucet Meeting
1. Flip off the water provide to your faucet. That is usually finished by closing the valves beneath the sink.
2. Disconnect the water provide traces. Use a wrench to loosen the nuts that join the provision traces to the tap.
3. Take away the mounting nuts. You will have to find the mounting nuts that safe the tap to the sink. These nuts are usually situated beneath the sink.
4. Pull the tap up and out of the sink. As soon as the mounting nuts have been eliminated, you’ll be able to pull the tap up and out of the sink.
5. Disconnect the tap deal with. The tap deal with is usually hooked up to the tap physique with a screw or a set screw. Use a screwdriver or a wrench to take away the screw or set screw and detach the deal with.
6. Take away the tap cartridge. The tap cartridge is situated inside the tap physique. Use a wrench or a screwdriver to take away the cartridge.
7. Clear the tap physique. As soon as the cartridge has been eliminated, you’ll be able to clear the tap physique with a light detergent and water.
8. Reassemble the tap. Reassemble the tap within the reverse order of disassembly.
| Element | Elimination |
|---|---|
| Water provide traces | Use a wrench to loosen the nuts that join the provision traces to the tap. |
| Mounting nuts | Find the mounting nuts that safe the tap to the sink and take away them. |
| Faucet deal with | Take away the screw or set screw that secures the deal with to the tap physique. |
| Faucet cartridge | Use a wrench or a screwdriver to take away the cartridge from the tap physique. |
Cleansing the Set up Space
After getting gathered your instruments and supplies, it’s time to begin prepping the set up space. This consists of cleansing the tap and sink, in addition to eradicating any outdated sealant or caulk. Listed below are some suggestions for cleansing the set up space:
Clear the Faucet
Use a light dish cleaning soap and heat water to scrub the tap. You’ll want to rinse the tap completely and dry it with a clear material.
Clear the Sink
Clear the sink utilizing a light dish cleaning soap and heat water. You’ll want to rinse the sink completely and dry it with a clear material.
Take away Outdated Sealant or Caulk
If there may be any outdated sealant or caulk across the faucet, take away it utilizing a utility knife or a caulk remover. Watch out to not harm the sink or countertop.
| Extra Suggestions for Cleansing the Set up Space |
|---|
| Use a degreaser to take away any grease or grime from the tap and sink. |
| Use a toothbrush to scrub any hard-to-reach areas. |
| Rinse the tap and sink completely with clear water. |
| Dry the tap and sink with a clear material. |
Putting in the New Faucet Meeting
1. Collect your instruments and supplies. You will have a brand new faucet meeting, a wrench, a screwdriver, and a pair of pliers.
2. Shut off the water provide to the tap. One can find the shut-off valves beneath the sink.
3. Disconnect the water traces from the outdated faucet. Use a wrench to loosen the nuts that maintain the traces in place.
4. Take away the outdated faucet. Use a screwdriver to take away the screws that maintain the tap in place. Then, raise the tap out of the sink.
5. Clear the mounting floor. Use a moist material to scrub the world the place the brand new faucet might be put in.
6. Set up the brand new faucet. Place the brand new faucet within the mounting gap and safe it with the screws.
7. Join the water traces to the brand new faucet. Use a wrench to tighten the nuts that maintain the traces in place. You’ll want to tighten the nuts securely, however don’t overtighten them.
| Step | Description |
|---|---|
| 1 | Collect your instruments and supplies. |
| 2 | Shut off the water provide to the tap. |
| 3 | Disconnect the water traces from the outdated faucet. |
| 4 | Take away the outdated faucet. |
| 5 | Clear the mounting floor. |
| 6 | Set up the brand new faucet. |
| 7 | Join the water traces to the brand new faucet. |
| Step | Motion |
|---|---|
| 1 | Find the water provide valves beneath the sink. |
| 2 | Flip the handles clockwise to open the water provide. |
| 3 | Examine to ensure that the water is flowing freely from the tap. |
| 4 | As soon as the water is flowing freely, you’ll be able to start uninstalling the tap. |
Supplies You will Want
Here’s a checklist of instruments you will want:
- Wrench
- Pliers
- Basin wrench (non-obligatory)
- Bucket
- Material
- New faucet
Step-by-Step Directions
- Flip off the water provide.
- Place a bucket beneath the tap to catch any water.
- Disconnect the water provide traces.
- Take away the mounting nuts.
- Pull the tap out of the sink.
- Clear the sink and tap mount.
- Set up the brand new faucet.
- Join the water provide traces.
- Activate the water provide.
- Examine for leaks.
Troubleshooting Widespread Points
1. Faucet is caught.
If the tap is caught, strive utilizing a wrench to loosen it. If that does not work, you’ll be able to strive utilizing a penetrating oil to loosen the threads.
2. Water is leaking from the tap.
If water is leaking from the tap, strive tightening the mounting nuts. If that does not work, you could want to exchange the O-rings or washers.
3. Faucet deal with is free.
If the tap deal with is free, strive tightening the screws that maintain it in place. If that does not work, you could want to exchange the deal with.
4. Faucet is just not spraying correctly.
If the tap is just not spraying correctly, strive cleansing the aerator. If that does not work, you could want to exchange the aerator.
5. Faucet is making a noise.
If the tap is making a noise, strive tightening the nuts that maintain it in place. If that does not work, you could have to lubricate the transferring elements.
6. Faucet is just not turning off utterly.
If the tap is just not turning off utterly, strive cleansing the seat washer. If that does not work, you could want to exchange the seat washer.
7. Faucet is dripping.
If the tap is dripping, strive tightening the packing nut. If that does not work, you could want to exchange the packing nut.
8. Faucet is just not working in any respect.
If the tap is just not working in any respect, strive checking {the electrical} provide. If that does not work, you could want to exchange the tap.
9. Faucet is leaking from the bottom.
If the tap is leaking from the bottom, strive tightening the mounting nuts. If that does not work, you could want to exchange the O-rings or washers.
10. Faucet is just not degree.
If the tap is just not degree, strive adjusting the mounting nuts. If that does not work, you could have to shim the tap.
How To Uninstall Kitchen Faucet
To uninstall a kitchen faucet, you will want the next instruments:
– Adjustable wrench
– Pliers
– Screwdriver
– Bucket
1. Flip off the water provide to the tap. There might be two shut-off valves beneath the sink, one for the new water and one for the chilly water. Flip each of those valves clockwise till they’re utterly closed.
2. Open the tap to launch any remaining water strain.
3. Disconnect the water provide traces from the tap. Use an adjustable wrench to loosen the nuts that maintain the traces in place. As soon as the nuts are free, you’ll be able to pull the traces off of the tap.
4. Take away the mounting nuts. There might be two mounting nuts that maintain the tap in place. Use an adjustable wrench to loosen these nuts. As soon as the nuts are free, you’ll be able to raise the tap out of the sink.
5. Clear the sink floor. As soon as the tap is eliminated, you’ll be able to clear the sink floor the place the tap was put in. Use a moist material to wipe away any grime or particles.
