The error message “Waste Toner Full” on Canon IR copiers may be irritating, particularly when it isn’t an correct reflection of the toner stage. This error can happen attributable to defective sensors or different inner points, and it will possibly forestall you from utilizing your copier till the error is resolved. As an alternative of calling a technician or changing the toner cartridge, you’ll be able to strive some easy methods to reset the error and get your copier working once more.
To trick the Canon IR copier into pondering that the waste toner cartridge will not be full, you’ll be able to first strive resetting the copier. Flip the copier off and unplug it from the ability outlet. Wait 30 seconds, then plug the copier again in and switch it on. This will likely clear the error message and assist you to proceed utilizing the copier as regular.
If resetting the copier doesn’t resolve the problem, you’ll be able to strive manually resetting the waste toner sensor. Open the entrance cowl of the copier and find the waste toner sensor. It’s normally a small, black sensor positioned close to the waste toner cartridge. Gently push the sensor down and launch it. This will likely reset the sensor and clear the error message. If the error message persists, you might want to scrub the waste toner sensor or exchange the waste toner cartridge.
Resetting the Waste Toner Counter
Comply with these detailed steps to reset the waste toner counter in your Canon IR printer:
Step 1: Entry Service Mode
Activate the printer and maintain down the “Cease” button whereas urgent the “Menu” button.
Step 2: Reset Waste Toner Counter
Navigate to the “Operate” menu utilizing the arrow keys, then choose “Knowledgeable Adjustment” → “Printer Setting” → “Waste Toner Counter”.
Use the numeric keypad to enter the next code: 8041873590.
Press the “Enter” button to reset the waste toner counter.
Step 3: Exit Service Mode
Press the “Cease” button to exit Service Mode.
Extra Notes:
After resetting the waste toner counter, you might want to exchange the waste toner bottle to stop future errors.
The particular steps for resetting the waste toner counter might range barely relying in your Canon IR printer mannequin. Seek the advice of the consumer handbook for particular directions.
| Canon IR Printer Mannequin | Service Mode Entry Code |
|---|---|
| Canon IR 2520 | 8041873590 |
| Canon IR 2525 | 8041873590 |
| Canon IR 2530 | 8041873584 |
Disabling the Waste Toner Sensor
Step 1: Collect Supplies
You will want the next supplies:
- A small Phillips head screwdriver
- A pair of needle-nose pliers
- A roll {of electrical} tape
Step 2: Find the Waste Toner Sensor
The waste toner sensor is positioned on the underside of the printer, close to the waste toner bin. It’s a small, plastic sensor with two wires linked to it.
Step 3: Disconnect the Sensor Wires
Use the needle-nose pliers to fastidiously disconnect the 2 wires from the sensor.
Step 4: Tape the Sensor Wires Collectively
Wrap the 2 sensor wires along with a small piece {of electrical} tape. This can forestall the printer from detecting the waste toner sensor and triggering the “waste toner full” error.
Remember to wrap the tape tightly across the wires, however not so tightly that you simply harm them. As soon as the wires are taped collectively, you’ll be able to reassemble the printer and switch it again on.
The printer ought to now have the ability to function with out triggering the “waste toner full” error.
**Be aware:** Disabling the waste toner sensor will forestall the printer from warning you when the waste toner bin is full. This might result in toner spills and different issues. It is very important examine the waste toner bin repeatedly and empty it when obligatory.
Cleansing the Waste Toner Bottle
To wash the waste toner bottle, comply with these steps:
-
Flip off the printer and unplug it from the ability outlet.
-
Open the entrance cowl of the printer.
-
Find the waste toner bottle.
-
Take away the waste toner bottle from the printer.
-
Empty the waste toner from the bottle right into a trash can. Watch out to not spill any toner.
-
Rinse the waste toner bottle with chilly water. Remember to rinse the entire toner out of the bottle.
-
Dry the waste toner bottle with a clear material.
-
Reinsert the waste toner bottle into the printer.
-
Shut the entrance cowl of the printer.
-
Plug the printer again into the ability outlet and switch it on.
-
Press the “Menu” button on the printer’s management panel.
-
Use the arrow keys to navigate to the “Upkeep” menu and press the “OK” button.
-
Use the arrow keys to navigate to the “Waste Toner Counter Reset” choice and press the “OK” button.
-
Press the “OK” button to reset the waste toner counter.
- Flip off the printer.
- Unplug the ability wire from the again of the printer.
- Wait 30 seconds.
- Plug the ability wire again into the printer.
- Activate the printer.
- Await the printer to heat up and initialize.
- Verify if the waste toner full error message has been resolved.
- If the error message persists, comply with the extra troubleshooting steps beneath.
- Flip off the printer and unplug it from the ability outlet.
- Open the entrance cowl of the printer.
- Find the waste toner container. It’s normally a black plastic container positioned on the correct aspect of the printer.
- Pull the waste toner container out of the printer.
- Empty the waste toner right into a trash can.
- Reinsert the waste toner container into the printer.
- Shut the entrance cowl of the printer.
- Plug the printer again into the ability outlet and switch it on.
Resetting the Waste Toner Counter
After getting cleaned the waste toner bottle, you’ll want to reset the waste toner counter. To do that, comply with these steps:
Unplugging the Printer and Restarting
If you happen to obtain a waste toner full error message in your Canon Ir printer, you’ll be able to attempt to reset the printer by unplugging it and restarting it. This can clear the printer’s reminiscence and should resolve the error message.
Steps for Unplugging and Restarting the Printer:
Fixing the Waste Toner Full Error
Resetting the Counter
1. Flip off the printer and unplug it from the ability outlet.
2. Maintain down the “Cease” button and plug the printer again in.
3. Proceed holding the “Cease” button for 10 seconds.
4. Launch the “Cease” button and the printer will reset the waste toner counter.
Changing the Waste Toner Container
1. Open the entrance cowl of the printer.
2. Find the waste toner container and pull it out.
3. Take away the brand new waste toner container from its packaging.
4. Insert the brand new waste toner container into the printer.
5. Shut the entrance cowl.
Cleansing the Waste Toner Sensor
1. Open the entrance cowl of the printer.
2. Find the waste toner sensor and clear it with a cotton swab.
3. Shut the entrance cowl.
Checking the Fuser Unit
1. Open the again cowl of the printer.
2. Find the fuser unit and take away it.
3. Examine the fuser unit for any harm or particles.
4. Clear the fuser unit with a smooth material or vacuum cleaner.
5. Reinstall the fuser unit.
Checking the Switch Belt
1. Open the entrance cowl of the printer.
2. Find the switch belt and take away it.
3. Examine the switch belt for any harm or particles.
4. Clear the switch belt with a smooth material or vacuum cleaner.
5. Reinstall the switch belt.
Checking the Imaging Unit
1. Open the entrance cowl of the printer.
2. Find the imaging unit and take away it.
3. Examine the imaging unit for any harm or particles.
4. Clear the imaging unit with a smooth material or vacuum cleaner.
5. Reinstall the imaging unit.
Checking the Paper Tray
1. Open the paper tray of the printer.
2. Examine the paper tray for any obstructions or particles.
3. Take away any obstructions or particles and reload the paper.
Checking the Energy Provide
1. Unplug the printer from the ability outlet.
2. Wait 30 seconds.
3. Plug the printer again into the ability outlet.
| Error Code | Description |
|---|---|
| E000 | Waste toner container full |
| E001 | Waste toner sensor soiled |
| E002 | Fuser unit malfunction |
| E003 | Switch belt malfunction |
| E004 | Imaging unit malfunction |
| E005 | Paper tray empty |
| E006 | Energy provide malfunction |
How To Trick Waste Toner Full Error On Canon Ir
If you happen to’re getting a “waste toner full” error in your Canon IR printer, it implies that the waste toner container is full and must be emptied. You possibly can empty the waste toner container your self, nevertheless it’s essential to comply with the directions fastidiously to keep away from damaging the printer.
Listed here are the steps on the right way to empty the waste toner container on a Canon IR printer:
If you happen to proceed to get a “waste toner full” error after following these steps, there could also be an issue with the printer. You possibly can contact Canon buyer help for help.
Individuals Additionally Ask
How do I bypass the waste toner full error on a Canon Ir?
There is no such thing as a method to bypass the waste toner full error on a Canon Ir. The waste toner container should be emptied when it’s full as a way to forestall harm to the printer.
How do I reset the waste toner counter on a Canon Ir?
You can not reset the waste toner counter on a Canon Ir. The waste toner counter is a everlasting document of the quantity of waste toner that has been collected by the printer. It can’t be reset or altered.
How typically ought to I empty the waste toner container on a Canon Ir?
The waste toner container needs to be emptied when it’s full. The frequency with which you’ll want to empty the waste toner container will range relying on how typically you employ the printer and the kind of paper that you simply use.
