5 Steps to Disassemble a Keurig Coffee Maker

Are you experiencing points along with your Keurig espresso maker and suspect that it’d require disassembly? Disassembling a Keurig is usually a daunting job, however with the appropriate steering and a bit little bit of endurance, it may be efficiently completed. Learn on to find a step-by-step information to disassemble your Keurig, permitting you to diagnose and deal with any underlying issues. Bear in mind, should you’re not assured in your skill to disassemble the machine, it is at all times advisable to hunt skilled help from a licensed restore technician.

Earlier than embarking on the disassembly course of, guarantee you might have gathered the required instruments. You will require a set of screwdrivers (Phillips and Torx), a plastic spudger, and a pair of needle-nose pliers. Moreover, put aside a clear and well-lit workspace to stop shedding small elements throughout disassembly. After getting every part ready, let’s delve into the step-by-step directions to disassemble your Keurig.

Firstly, unplug the Keurig from {the electrical} outlet and take away any water from the reservoir. Find the screws on the underside of the machine and thoroughly take away them utilizing the suitable screwdriver. Subsequent, use the plastic spudger to softly pry open the housing panels, ranging from the underside and dealing your means upwards. Be cautious to not apply extreme drive, because the panels might be fragile. As soon as the panels are indifferent, you may have entry to the inner elements of the Keurig. Proceed to the following steps within the information to additional disassemble the machine and establish the supply of any points chances are you’ll be experiencing.

Collect Mandatory Instruments

Disassembling a Keurig requires just a few important instruments. Collect the next gadgets earlier than starting the method:

Screwdrivers

You will have a set of Phillips and Torx screwdrivers in varied sizes. The particular sizes required might range relying in your Keurig mannequin. Check with your consumer handbook or on-line assets for the precise sizes wanted.

Accessing the Exit Needle

The exit needle, situated beneath the brew head, is important for the right supply of espresso. To entry it, you may have to fastidiously disassemble the Keurig machine. Here is a step-by-step information:

1. Take away the Drip Tray

Begin by eradicating the drip tray situated on the backside entrance of the machine. Merely slide it ahead and elevate it out.

2. Unplug the Machine

For security, unplug the Keurig from the ability outlet earlier than continuing additional.

3. Take away the Water Reservoir

Carry the water reservoir in the back of the machine and pull it straight out. Set it apart.

4. Open the Ok-Cup Holder

Press the Ok-Cup holder launch button and elevate the holder up and out of the machine.

5. Take away the Brew Head

This can be a essential step that requires finesse. Find the 2 small latches on the aspect of the brew head, simply above the Ok-Cup holder. Pinch the latches concurrently and pull the brew head straight up and out of the machine.

6. Entry the Exit Needle

As soon as the brew head is eliminated, you’ll be able to entry the exit needle situated at its backside. The needle is normally barely recessed and will require a small screwdriver or needle-nose pliers to take away it.

How one can Disassemble a Keurig

To disassemble a Keurig, you’ll need the next instruments:

• Phillips head screwdriver
• Flathead screwdriver
• Hex key

Comply with these steps to disassemble your Keurig:

1. Unplug the Keurig from the ability outlet.
2. Take away the water reservoir.
3. Take away the drip tray.
4. Take away the screws that maintain the highest cowl in place.
5. Carry off the highest cowl.
6. Take away the screws that maintain the water heater in place.
7. Carry out the water heater.
8. Take away the screws that maintain the pump in place.
9. Carry out the pump.
10. Take away the screws that maintain the management panel in place.
11. Carry out the management panel.
12. Take away the screws that maintain the bottom in place.
13. Carry off the bottom.

Individuals Additionally Ask

How do I take away the needle from a Keurig?

To take away the needle from a Keurig, you’ll need to make use of a pair of needle-nose pliers. Grasp the needle firmly with the pliers and pull it straight out of the machine.

How do I exchange the heating ingredient in a Keurig?

To switch the heating ingredient in a Keurig, you’ll need to comply with these steps:

1. Unplug the Keurig from the ability outlet.
2. Take away the screws that maintain the highest cowl in place.
3. Carry off the highest cowl.
4. Find the heating ingredient.
5. Disconnect the wires from the heating ingredient.
6. Take away the screws that maintain the heating ingredient in place.
7. Carry out the heating ingredient.
8. Set up the brand new heating ingredient.
9. Safe the heating ingredient with the screws.
10. Join the wires to the heating ingredient.
11. Change the highest cowl.
12. Safe the highest cowl with the screws.
13. Plug the Keurig again into the ability outlet.