Upgrading your rest room’s aesthetics or performance usually includes tackling plumbing tasks, and putting in a brand new tub drain is one such job. Whether or not you are changing a worn-out drain or customizing your tub’s look, putting in a drain is a manageable DIY challenge with the fitting instruments and know-how. This complete information will give you step-by-step directions, making certain a seamless set up that leaves your tub trying refreshed and functioning optimally.
Earlier than embarking on the set up course of, collect the required instruments and supplies. You may want a brand new tub drain meeting, a plumber’s putty, a putty knife, an adjustable wrench, a screwdriver, and a flashlight. After you have all the things you want, guarantee the bath is empty and the water provide is shut off. Security needs to be paramount, so put on gloves and eye safety in the course of the set up.
With preparation full, the set up can start. Start by eradicating the outdated drain meeting. Use the adjustable wrench to loosen the drain flange and carry it off. Clear the drainpipe opening totally, eradicating any particles or outdated putty. Apply a beneficiant bead of plumber’s putty across the base of the brand new drain flange and thoroughly place it over the drainpipe opening. Tighten the flange utilizing the wrench, making certain it is safe however not overtightened. Lastly, set up the drain stopper and overflow plate, and also you’re all set! Double-check for any leaks by working water into the bathtub and inspecting the drain for correct drainage.
Gathering Mandatory Supplies
To start your tub drain set up, you will want to collect the required supplies. This is an in depth checklist to make sure you have all the things you want readily available:
Instruments
| Qty. | Device |
|---|---|
| 1 | Adjustable wrench or channel-type pliers |
| 1 | Phillips screwdriver |
| 1 | Flathead screwdriver |
| 1 | Putty knife |
| 1 | Plumber’s putty |
| 1 | Rags or paper towels |
Supplies
| Qty. | Half |
|---|---|
| 1 | Tub drain meeting (consists of stopper and flange) |
| 2 | Washers (normally included with tub drain meeting) |
| 1 | Tub drain gasket (if not already put in on tub drain meeting) |
Eradicating the Outdated Drain
Step 1: Begin by eradicating the drain cowl and the strainer. Use a screwdriver or pliers to softly pry the drain cowl off, being cautious to not injury it.
Step 2: As soon as the drain cowl is eliminated, you will note the drain flange. The drain flange is the metallic piece that connects the drain to the bathtub. Unscrew the drain flange by turning it counterclockwise. If the flange is simply too tight to take away by hand, you need to use a wrench.
Step 3: As soon as the drain flange is eliminated, you will note the drain pipe. The drain pipe is the pipe that carries water from the bathtub to the drain. Unscrew the drain pipe by turning it counterclockwise. If the pipe is simply too tight to take away by hand, you need to use a wrench.
| Step | Motion |
|---|---|
| 1 | Take away drain cowl and strainer |
| 2 | Unscrew drain flange |
| 3 | Unscrew drain pipe |
Step 4: As soon as the drain pipe is eliminated, you may take away the outdated drain meeting. The outdated drain meeting is the metallic or plastic piece that’s positioned on the backside of the drain pipe. To take away the outdated drain meeting, merely pull it up and out of the drain pipe.
Cleansing the Drain Opening
After you have eliminated the outdated drain, you will need to totally clear the drain opening earlier than putting in the brand new one. This can assist to stop leaks and be sure that the brand new drain matches correctly. Listed below are some steps on the way to clear the drain opening:
Supplies you will want:
| Merchandise | Amount |
|---|---|
| Dry fabric or paper towels | A number of |
| Scrub brush | 1 |
| Baking soda | 1 cup |
| Vinegar | 1 cup |
1. Wipe away any particles. Use a dry fabric or paper towels to wipe away any hair, cleaning soap scum, or different particles which may be seen within the drain opening.
2. Scrub the drain opening. Use a scrub brush to wash the drain opening and take away any remaining particles. Be sure you scrub the edges of the opening in addition to the underside.
3. Pour baking soda and vinegar down the drain. Pour 1 cup of baking soda down the drain, adopted by 1 cup of vinegar. The baking soda and vinegar will react to create a fizzing motion that may assist to dissolve any remaining particles and disinfect the drain.
4. Let the answer sit for quarter-hour. Enable the baking soda and vinegar resolution to sit down within the drain for quarter-hour to provide it time to work. The fizzing motion will assist to interrupt down any remaining particles.
5. Flush the drain with scorching water. After quarter-hour, flush the drain with scorching water to rinse away any remaining baking soda and vinegar resolution. The new water may also assist to clear any remaining particles.
6. Examine the drain opening. After you have flushed the drain, examine the drain opening to ensure that it’s clear and freed from particles. If there’s nonetheless particles current, repeat steps 2-5.
Making use of Plumber’s Putty
Earlier than You Start
Collect your supplies: plumber’s putty, a putty knife, and a moist rag.
Steps
1. Clear the Drain Gap
Use a moist rag to take away any grime or particles from the drain gap. This can guarantee an excellent seal.
2. Kind a Putty Roll
Roll a small quantity of plumber’s putty into a protracted, skinny roll. The roll needs to be barely longer than the circumference of the drain gap.
3. Place the Putty
Place the putty roll across the drain gap, urgent it firmly into the opening. Use the putty knife to easy the putty out and create a watertight seal.
4. Create a Tapered Edge
Use the putty knife to create a slight taper on the outer fringe of the putty. This can assist forestall water from seeping underneath the seal.
| Tapering the Putty Edge |
|---|
| – Maintain the putty knife at a slight angle to the putty. |
| – Apply agency, even stress whereas pulling the knife in direction of you. |
| – Proceed tapering the putty till it varieties a skinny, watertight seal across the drain gap. |
Putting in the New Drain Meeting
**Step 1: Collect Supplies:** Gather all vital instruments and objects, together with the brand new drain meeting, plumber’s putty, tape, a wrench, and a screwdriver.
**Step 2: Take away the Outdated Drain:** Use a wrench to loosen the nuts holding the drain in place. Gently pull the outdated drain meeting out of the bathtub drain gap.
**Step 3: Clear the Drain Gap:** Totally clear the drain gap and floor round it with a sponge or brush to take away any particles or outdated sealant.
**Step 4: Apply Plumber’s Putty:** Roll out a rope of plumber’s putty and apply it liberally to the underside of the brand new drain flange. Clean out the putty to create a watertight seal.
**Step 5: Place and Set up the Drain Meeting:**
- Align the drain meeting over the drain gap and gently push it into the opening.
- Tighten the nuts on the underside of the flange by hand till cosy.
- Use a wrench to additional tighten the nuts steadily, alternating between sides to make sure even stress.
**Step 6: Set up the Overflow Plate (Non-obligatory):** In case your tub has an overflow drain, set up the overflow plate over the overflow gap utilizing screws or bolts.
**Step 7: Check the Drain:** Run water into the bathtub and verify for any leaks. If a leak happens, tighten the nuts or apply extra plumber’s putty to the flange.
Desk: Beneficial Instruments and Supplies
| Device/Materials | Function |
|---|---|
| Tub Drain Meeting | New drain meeting |
| Plumber’s Putty | Creates a watertight seal |
| Tape | For short-term sealing or marking |
| Wrench | To tighten nuts |
| Screwdriver | To safe overflow plate (if relevant) |
Tightening the Drain Meeting
As soon as the drain meeting is in place, it is time to tighten it. This can be sure that the seal is watertight and that the drain will operate correctly.
To tighten the drain meeting, you will want a wrench or a pair of pliers. Grip the drain flange with the wrench or pliers and switch it clockwise till it is cosy. Watch out to not overtighten the flange, as this might injury the drain.
As soon as the flange is tight, you may tighten the drain stopper. To do that, merely insert the stopper into the drain gap and switch it clockwise till it is cosy. Once more, watch out to not overtighten the stopper, as this might injury the drain.
This is a extra detailed have a look at the steps concerned in tightening the drain meeting:
| Step | Description |
|---|---|
| 1 | Place the rubber gasket on the drain flange. |
| 2 | Insert the drain flange into the drain gap. |
| 3 | Tighten the drain flange with a wrench or pliers. |
| 4 | Insert the drain stopper into the drain gap. |
| 5 | Tighten the drain stopper by turning it clockwise. |
| 6 | Test the seal across the drain meeting to ensure it is watertight. If vital, tighten the drain flange or drain stopper additional. |
Putting in the Washer
1. Place the washer over the drain opening and align the slots on the washer with the slots on the drain flange.
2. Insert the screws into the slots and tighten them utilizing a screwdriver or a wrench.
3. Apply a bead of plumber’s putty across the base of the washer.
4. Set up the drain cowl over the washer and tighten it.
5. Activate the water and verify for leaks. If there are leaks, tighten the screws or apply extra plumber’s putty.
6. As soon as the washer is put in, you may check it by filling the bathtub with water and permitting it to empty.
7. Troubleshooting Washer Issues
If the washer isn’t draining correctly, there could also be an issue with the washer itself or with the drain. Listed below are some frequent issues and the way to repair them:
| Downside | Resolution |
|---|---|
| The washer isn’t sealing correctly | Tighten the screws or apply extra plumber’s putty. |
| The drain is clogged | Take away the drain cowl and clear the clog. |
| The drainpipe is kinked or blocked | Straighten the drainpipe or take away the blockage. |
Securing the Overflow Plate
8. Set up the Overflow Plate Gasket
[content] The overflow plate is a skinny, flat metallic or plastic piece that covers the overflow gap within the tub. It has a gasket that helps to seal the plate in opposition to the bathtub, stopping water from leaking out.
To put in the overflow plate gasket:
1. Place the gasket on the overflow plate.
2. Heart the gasket over the overflow gap within the tub.
3. Press the gasket firmly into place.
| Tip: |
|---|
| If the gasket isn’t centered, water might leak out across the overflow plate. |
As soon as the gasket is in place, you may safe the overflow plate to the bathtub. To do that, merely insert the screws into the holes within the overflow plate and tighten them till the plate is safe.
Testing the Drain
As soon as the drain is put in, it is important to check it to make sure it is functioning appropriately. This is an in depth information on testing the drain:
1. Fill the Tub with Water
Fill the bathtub with water to a stage just under the overflow drain.
2. Open the Drain
Pull the drain plug or open the drain valve to permit water to empty.
3. Observe the Circulation Charge
Monitor the water stream price. It ought to drain rapidly and easily with none obstructions.
4. Test for Leaks
Examine the drain for any leaks. Guarantee there isn’t any water seeping from any joints or connections.
5. Hear for Noises
Because the water drains, pay attention for any uncommon noises, akin to gurgling or hissing. These noises might point out a clog or a problem with the plumbing system.
6. Refill the Tub
As soon as the bathtub is empty, refill it with water to check the drain seal.
7. Shut the Drain
Plug the drain or shut the valve to stop water from draining.
8. Wait A number of Hours
Enable the bathtub to sit down for a number of hours to verify for leaks.
9. Examine the Drain Seal
After ready, examine the drain seal for any water accumulation. If there isn’t any water current, the drain seal is functioning appropriately and there aren’t any leaks.
| Check | Consequence |
|---|---|
| Circulation price | Fast and easy |
| Leaks | No water seeping |
| Noises | No gurgling or hissing |
| Drain seal | No water accumulation after a number of hours |
Troubleshooting Frequent Issues
1. Water Leaking From the Drain
Test the drain stopper for correct match and exchange it if vital.Make sure the drain flange is securely tightened by hand and with a wrench. Re-caulk across the drain flange to stop leaks.
2. Drain Not Draining Correctly
Use a drain snake to take away hair or particles clogging the drain. If the clog persists, disassemble the drain and clear out the parts.
3. Drain is Gurgling
This means a blockage in the primary drain line. Test different drains in the home for gradual drainage.Contact a plumber to clear the primary drain line.
4. Drain is Making Noises
Free or worn parts could cause rattling or buzzing noises. Tighten or exchange the free elements, such because the drain stopper or overflow plate.
5. Drain is Overflowing
Test if the overflow drain is clogged or obstructed. Clear the overflow drain and guarantee it’s not blocked by particles.
6. Drain is Corroded
Rust or corrosion can result in leaks and injury. Take away the drain and clear it with a vinegar resolution. If corrosion is extreme, exchange the drain.
7. Drain is Free
The drain flange might have loosened over time. Tighten the flange by hand and with a wrench to safe it.
8. Drain is Discolored
Mineral deposits or onerous water can discolor the drain. Clear the drain with a business cleaner or use a vinegar resolution to take away discoloration.
9. Drain is Cracked
A cracked drain can result in leaks and needs to be changed instantly. Contact a plumber or set up a brand new drain your self by following the directions offered on this article.
10. Drain is Broken Past Restore
If the drain is extensively broken or corroded, it will not be repairable. On this case, you will want to take away the outdated drain and set up a brand new one, following the steps outlined on this article.
How To Set up A Tub Drain
Putting in a bath drain is a comparatively easy plumbing challenge that may be accomplished in a couple of hours. Nonetheless, you will need to observe the steps rigorously to make sure that the drain is put in correctly and won’t leak. Listed below are the steps on the way to set up a bath drain:
-
Take away the outdated drain. To do that, you will want to make use of a pair of pliers to loosen the nuts that maintain the drain in place. As soon as the nuts are free, you may pull the drain out of the bathtub.
-
Clear the drain gap. As soon as the outdated drain is eliminated, you will want to scrub the drain gap. Use a rag or a sponge to wipe away any particles or grime which will have collected within the gap.
-
Apply plumbers putty to the brand new drain. Plumbers putty is a kind of sealant that may assist to stop leaks across the drain. Apply a bead of plumbers putty to the underside of the brand new drain.
-
Insert the brand new drain into the drain gap. Align the drain with the drain gap and insert it into the opening. Press down on the drain till it’s seated firmly within the gap.
-
Tighten the nuts. Use a pair of pliers to tighten the nuts that maintain the drain in place. Be sure you tighten the nuts evenly in order that the drain is securely fixed.
-
Check the drain. As soon as the drain is put in, activate the water and verify for leaks. If there are any leaks, you will want to tighten the nuts additional.
Folks Additionally Ask About How To Set up A Tub Drain
What’s the easiest way to scrub a bath drain?
The easiest way to scrub a bath drain is to make use of a drain cleaner. Drain cleaners can be found in quite a lot of varieties, together with liquids, gels, and powders. Be sure you observe the instructions on the drain cleaner label rigorously.
How usually ought to I exchange my tub drain?
Tub drains needs to be changed each 5 to 10 years. Nonetheless, chances are you’ll want to exchange the drain sooner if it turns into clogged or broken.
Can I set up a bath drain myself?
Sure, you may set up a bath drain your self. Nonetheless, you will need to observe the steps rigorously to make sure that the drain is put in correctly and won’t leak.
