Changing a belt on a Maytag W10873035 dryer could look like a frightening job, nevertheless it’s a simple course of with the fitting instruments and a step-by-step information. Changing a worn or broken belt can restore your dryer’s performance and forestall additional points with the equipment. On this complete information, we’ll give you the mandatory steps, suggestions, and security precautions to make sure a profitable belt substitute course of.
Earlier than embarking on this undertaking, guarantee you could have the suitable instruments and security gear. You may want a brand new belt suitable together with your Maytag W10873035 dryer, a Phillips screwdriver, a flat-head screwdriver, and needle-nose pliers. Security must be paramount, so put on gloves and security glasses all through the method. Moreover, unplug the dryer from the ability outlet to stop electrical hazards.
As soon as you’ve got assembled your instruments and ensured security, you’ll be able to start the restore course of. Step one is to take away the dryer’s entrance panel. To do that, find the screws securing the panel and take away them utilizing the Phillips screwdriver. Fastidiously detach the entrance panel and set it apart in a secure place. Subsequent, find the belt situated across the drum and motor pulley. Use the flat-head screwdriver to pry the belt off the motor pulley. Lastly, take away the belt from the drum pulley by hand or with the assistance of needle-nose pliers.
Finding and Making ready Your Maytag W10873035
1. Unplugging the Equipment and Eradicating the Again Panel
Earlier than commencing any repairs or upkeep, guarantee the security of your work atmosphere by unplugging the Maytag W10873035 from its energy supply. Find the ability wire and disconnect it from the wall outlet. This important step minimizes the danger {of electrical} shock and makes the following steps safer.
Subsequent, determine the again panel of the equipment. This panel is often held in place by a number of screws situated round its perimeter. Utilizing an acceptable screwdriver, fastidiously take away these screws and set them apart for later use. As soon as the screws are eliminated, gently carry the again panel off the equipment and set it apart in a secure location.
With the again panel eliminated, you’ll achieve entry to the interior parts of the Maytag W10873035. Deal with these parts with care, as they’re delicate and important for the correct functioning of the equipment.
2. Figuring out the Belt
Find the drive belt, which is a versatile rubber band that connects the motor pulley to the transmission pulley. The belt is chargeable for transmitting energy from the motor to the transmission, enabling the equipment to function appropriately.
Fastidiously examine the situation of the belt. For those who observe any cracks, tears, or extreme put on, it signifies that the belt must be changed. A broken belt can hinder the correct functioning of the equipment and will even result in pricey repairs.
3. Eradicating and Changing the Belt
Earlier than eradicating the outdated belt, take a second to familiarize your self with its routing. Word the trail it takes from the motor pulley to the transmission pulley. This info shall be useful when putting in the brand new belt.
To take away the outdated belt, merely slip it off the pulleys. Watch out to not harm the pulleys or the belt itself. As soon as the outdated belt is eliminated, completely clear the pulleys with a dry fabric to take away any filth or particles that will have an effect on the efficiency of the brand new belt.
Now, take the brand new belt and align it with the pulleys in accordance with the routing you noticed earlier. Gently slip the belt onto the pulleys, guaranteeing that it’s securely seated. Double-check the belt stress and modify it if obligatory.
Instruments Required for the Set up
1. Screwdriver
A screwdriver is used to take away the again panel of the washer and to loosen the stress on the belt. A Phillips head screwdriver is often required for this job.
2. Belt Pressure Gauge
A belt stress gauge is a specialised instrument used to measure the stress of the belt. This instrument will not be important, however it will probably assist be certain that the belt is correctly tensioned and can last more.
use a belt stress gauge:
a. Place the gauge over the belt and pull it tight.
b. Learn the stress studying on the gauge.
c. The proper stress will differ relying on the washer mannequin and the kind of belt. Consult with the washer’s consumer guide for the advisable stress setting.
3. Socket or Wrench Set
A socket or wrench set is required to take away the motor mount bolts that maintain the motor in place. The scale of the bolts will differ relying on the washer mannequin.
| Software | Description |
|---|---|
| Screwdriver | Used to take away the again panel and loosen belt stress. |
| Belt Pressure Gauge | Measures the stress of the belt. |
| Socket or Wrench Set | Removes the motor mount bolts. |
Eradicating the Previous Belt
Step 3: Take away the Previous Belt
Now, let’s get right down to enterprise and take away that outdated belt that is been holding you again (we’re speaking in regards to the belt in your washer, not your life). However do not fret; it is a simple course of when you observe these detailed steps:
- Find the motor pulley behind the washer’s rear panel. This pulley has a groove the place the belt suits snugly.
- Use a flat-head screwdriver or your fingers to softly pry the outdated belt off the motor pulley. Watch out to not harm the pulley or the belt throughout this course of.
- As soon as the belt is free of the motor pulley, transfer it towards the middle of the washer tub. Then, rotate the bathtub by hand whereas concurrently pulling the belt upwards and outwards. This movement will assist the belt slide off the bathtub pulley and out of the washer.
Word: If the outdated belt is especially caught, you need to use a pair of pliers to help you. Nonetheless, guarantee to not apply extreme pressure, because it may tear the belt.
Choosing the Right Substitute Belt
To make sure a profitable set up, choosing the fitting substitute belt is essential. Consult with your Maytag equipment’s mannequin quantity (W10873035) to find out the particular belt required. Moreover, seek the advice of the equipment’s consumer guide or contact Maytag buyer assist for additional steering.
A number of components must be thought of when choosing your belt:
-
Size: The belt’s size ought to exactly match the unique’s dimensions. Incorrect size could have an effect on the washer’s efficiency and may result in points resembling belt slippage or extreme stress.
-
Width: The belt’s width should additionally correspond to the unique half. A slim belt could slip, whereas a large one could rub in opposition to the washer’s inside parts, inflicting harm.
-
Ribbing: V-belts function a ridged sample on their interior floor. The quantity and spacing of those ribs ought to match these of the unique belt for optimum energy transmission and efficiency.
This is a desk summarizing the important thing belt specs for Maytag washer mannequin W10873035:
| Specification | Worth |
|---|---|
| Size | 82.6″ |
| Width | 0.5″ |
| Ribbing | 4 ribs |
Putting in the New Belt
To interchange the outdated belt with the brand new one, observe these steps:
1. Flip the Washer
Unplug the washer and switch off the water provide. Tilt the washer again to entry the underside.
2. Take away the Again Panel
Find the 4 screws holding the again panel in place and take away them. Fastidiously carry off the panel.
3. Find the Belt
Inside, you may see the outdated belt wrapped across the motor pulley and the drum pulley. Word the routing of the belt.
4. Take away the Previous Belt
Use a flashlight to find the tensioner pulley. Pry the belt off the tensioner pulley utilizing a flat-head screwdriver or needle-nose pliers.
5. Set up the New Belt
Begin by wrapping the brand new belt across the motor pulley. Make sure the belt is correctly aligned within the grooves.
Then, place the belt over the tensioner pulley.
Subsequent, whereas making use of stress to the belt, slip it onto the drum pulley.
Lastly, launch the stress on the belt and guarantee it is correctly seated within the pulleys.
6. Reattach the Again Panel
Place the again panel again onto the washer and safe it with the screws.
7. Take a look at the Washer
Plug the washer again in, activate the water provide, and run a spin cycle to confirm the brand new belt is functioning appropriately.
Tensioning the Belt
To stress the belt correctly, first find the loafer pulley. This pulley is often situated on the prime or backside of the washer.
After you have discovered the loafer pulley, use a wrench or pliers to loosen the bolt that secures it. Then, rotate the loafer pulley till the belt is taut. Watch out to not overtighten the belt, as this could harm the pulley or the belt.
As soon as the belt is tight, tighten the bolt that secures the loafer pulley. Then, run the washer by means of a take a look at cycle to make sure that the belt is tensioned correctly.
Checking Belt Pressure
To examine the belt stress, use a stress gauge. A stress gauge is a instrument that measures the pressure required to deflect the belt a sure distance. The proper belt stress for a Maytag W10873035 washer is 15-20 kilos.
If the belt stress is just too low, the belt could slip off the pulleys. If the belt stress is just too excessive, the belt could stretch or break.
Pressure Gauge Readings
The next desk exhibits the everyday stress gauge readings for a Maytag W10873035 washer:
| RPM | Pressure (lbs) |
|---|---|
| 600 | 15-20 |
| 800 | 18-22 |
| 1000 | 20-24 |
Disconnect the Washer from Energy
Start by unplugging the Maytag washer from its energy supply. This step is essential for security, as it would forestall unintended activation or electrical shocks throughout belt set up.
Take away the Washer’s Again Panel
Find the entry panel on the again of the washer. Use a screwdriver or a socket wrench to take away the screws holding the panel in place and gently detach it from the unit.
Find and Take away the Drive Belt
As soon as the again panel is eliminated, the drive belt shall be seen. It connects the washer’s motor to the transmission and is chargeable for rotating the drum. Grip the belt firmly and slide it off the pulleys.
Examine the Belt for Injury
Examine the outdated belt completely for indicators of injury, resembling cracks, fraying, or extreme put on. If any harm is discovered, it’s important to exchange the belt instantly.
Set up the New Belt
Align the brand new belt with the pulleys on the motor and transmission. Slip the belt onto the pulleys, guaranteeing it suits snugly. Rotate the drum by hand to stress the belt and examine for correct alignment.
Reattach the Again Panel
As soon as the belt is put in, reposition the again panel onto the washer. Safe it firmly utilizing the screws or bolts that had been eliminated earlier.
Troubleshooting Frequent Belt Set up Points
7. The Washer Does not Spin After Belt Substitute
If the washer would not spin after belt substitute, examine the next:
| Doable Trigger | Resolution |
|---|---|
| Damaged or unfastened wire connections | Examine wire connections between the motor, transmission, and management board; tighten or restore any unfastened connections. |
| Defective motor or transmission | Examine the motor and transmission for indicators of injury or put on; exchange if obligatory. |
| Management board difficulty | Reset the management board by unplugging the washer for 60 seconds; seek the advice of a certified technician if the difficulty persists. |
Security Issues Throughout Set up
Private Security
1. Put on acceptable security gear, together with gloves and security glasses.
2. Disconnect the equipment from the ability supply earlier than starting any work.
3. Be certain that the work space is well-lit and freed from tripping hazards.
Equipment Stability
4. Place the washer on a steady and degree floor.
5. Degree the equipment utilizing the adjustable ft.
6. Don’t place the washer on a carpet or different smooth floor that will trigger it to tip.
Electrical Security
7. Be certain that {the electrical} outlet you’re utilizing is suitable with the washer’s voltage and amperage necessities.
8. Use a surge protector or uninterruptible energy provide (UPS) to guard the washer from electrical surges or outages.
9. Don’t overload {the electrical} circuit with a number of home equipment.
| Electrical Security Measures |
|---|
| Use a surge protector or UPS |
| Guarantee correct air flow |
| Don’t overload electrical circuits |
| Commonly examine wiring and connections |
| Contact a certified electrician for electrical points |
By following these security concerns, you’ll be able to guarantee a secure and profitable set up of the Maytag W10873035 washer.
Changing the Belt on Maytag W10873035
1. Unplug the washer and switch off the water provide.
2. Take away the again panel of the washer by unscrewing the screws that maintain it in place.
3. Find the drive belt and take away it by pulling it off the pulleys.
4. Set up the brand new belt by slipping it over the pulleys and ensure that the belt is correctly aligned.
5. Exchange the again panel and tighten the screws.
6. Reconnect the water provide and plug within the washer.
Common Upkeep Tricks to Lengthen Belt Life
7. Clear the lint filter commonly to stop lint and particles from increase on the belt.
8. Keep away from overloading the washer, as this could put further pressure on the belt.
9. Examine the belt for put on and tear commonly. For those who discover any cracks or fraying, exchange the belt instantly.
Listed below are some extra suggestions for extending the lifetime of your washer belt:
| Tip | Description |
|---|---|
| Run smaller hundreds | Smaller hundreds put much less stress on the belt and motor. |
| Use chilly water | Sizzling water can harm the belt over time. |
| Keep away from utilizing bleach | Bleach can weaken the belt. |
| Unplug the washer when not in use | It will assist to stop energy surges from damaging the belt. |
Supplies You may Want:
- New belt
- Screwdriver
- Socket wrench
Step-by-Step Directions:
- Unplug the washer from the ability outlet.
- Flip off the water provide to the washer.
- Disconnect the hoses from the again of the washer.
- Lay the washer on its aspect.
- Take away the underside panel of the washer.
- Find the motor and transmission.
- Take away the outdated belt from the motor and transmission.
- Set up the brand new belt onto the motor and transmission.
- Tighten the belt by adjusting the tensioner.
- Reinstall the underside panel of the washer.
- Join the hoses to the again of the washer.
- Activate the water provide to the washer.
- Plug the washer into the ability outlet.
- Take a look at the washer to ensure it is working correctly.
10. Troubleshooting:
For those who’re having bother putting in the belt, listed here are some suggestions:
- Be sure that the brand new belt is the proper dimension on your washer.
- Be sure that the belt is put in appropriately on the motor and transmission.
- Be sure that the belt is tight sufficient, however not too tight.
- For those who’re nonetheless having bother, name a certified equipment restore technician.
Further Sources for Reference:
| Useful resource | Hyperlink |
|---|---|
| Maytag W10873035 Belt Set up Video | https://www.youtube.com/watch?v=123456789 |
| Maytag W10873035 Belt Substitute Directions | https://www.appliancepartspros.com/repair-help/how-to-replace-a-washer-belt |
Set up the Belt on a Maytag Washer W10873035
Changing the belt on a Maytag washer mannequin W10873035 is a comparatively simple job that may be accomplished in about half-hour with the fitting instruments and components.
Step-by-Step Directions
- Collect the mandatory instruments: You will want a Phillips screwdriver, a flathead screwdriver, and a brand new drive belt (half quantity W10873035).
- Disconnect the ability: Unplug the washer from {the electrical} outlet.
- Take away the again panel: Use the Phillips screwdriver to take away the 2 screws that maintain the again panel in place. Elevate the panel off and set it apart.
- Find the motor pulley: The motor pulley is a big, grooved wheel situated on the backside of the washer.
- Take away the outdated belt: Use the flathead screwdriver to pry the outdated belt off the motor pulley.
- Set up the brand new belt: Place the brand new belt across the motor pulley and the transmission pulley (situated on the prime of the washer).
- Tighten the belt: Push the motor pulley in the direction of the again of the washer to tighten the belt.
- Reinstall the again panel: Place the again panel again onto the washer and safe it with the screws.
- Reconnect the ability: Plug the washer again into {the electrical} outlet.
Folks Additionally Ask
How do I do know if the belt on my Maytag washer is damaged?
Indicators of a damaged or broken belt embody a loud washer, problem agitating or spinning garments, and a burning scent.
Can I set up a special belt on my Maytag washer?
No, you will need to use the proper belt specified on your Maytag washer mannequin.
How usually ought to I exchange the belt on my Maytag washer?
The belt must be changed each 5-7 years to keep up optimum efficiency.
