Upgrading the hand grips in your Electra Glide Normal is an easy activity that may considerably improve your using expertise. Whether or not you are on the lookout for improved consolation, higher management, or a contact of personalization, putting in new hand grips is an efficient and cost-effective answer. This information will give you step-by-step directions, together with useful ideas and methods, to make sure a profitable and satisfying set up.
To start, collect the mandatory supplies: a set of alternative hand grips, a small flathead screwdriver, a pair of pliers, and a degreaser. Upon getting every little thing you want, let’s dive into the set up course of. Firstly, take away the outdated hand grips by fastidiously inserting the flathead screwdriver into the hole between the grip and the handlebar. Gently pry the grip unfastened whereas twisting it forwards and backwards. Use the pliers to take away the grip utterly.
Earlier than putting in the brand new hand grips, it is essential to wash the handlebars totally. Use the degreaser to take away any filth, oil, or particles that would intervene with the adhesion of the grips. Enable the handlebars to dry utterly earlier than continuing. Subsequent, apply a skinny layer of adhesive to the interior floor of the hand grips. This can assist to safe them in place. Rigorously align the hand grips with the handlebars and firmly push them on. Be sure that they’re positioned accurately and that there aren’t any gaps or air bubbles. As soon as the hand grips are put in, regulate them to a cushty place and tighten any screws or clamps as vital. Congratulations, you have got efficiently upgraded the hand grips in your Electra Glide Normal, including a contact of consolation and elegance to your journey.
Preparation and Security Precautions
Preparation:
Earlier than embarking on the set up course of, it’s essential to make sure correct preparation to ensure a easy and protected expertise. Provoke by gathering important instruments, together with a Phillips head screwdriver, 5/16 inch hex socket, T-27 Torx screwdriver, and loctite threadlocker blue. Assemble clear rags for wiping and a small hammer for tapping the grips into place.
Subsequent, disconnect the battery’s destructive terminal to forestall any electrical hazards. Take away the handlebars from the motorbike by unbolting the 4 pinch bolts utilizing the 5/16 inch hex socket. Rigorously elevate the handlebars upwards and away from the bike, taking care to not injury the wiring or cables.
Find the throttle meeting on the proper handlebar and take away the three screws securing the throttle housing utilizing the Phillips head screwdriver. Gently slide the throttle housing out to reveal the throttle grip. Repeat this course of on the left handlebar for the clutch grip.
Security Precautions:
To make sure security all through the set up, adhere to the next precautions meticulously:
- Put on acceptable security gear, together with gloves and eye safety.
- Work in a well-ventilated space to reduce publicity to fumes.
- Examine the brand new hand grips totally earlier than set up to make sure they’re undamaged.
- Keep away from overtightening any screws or bolts, as this might injury the parts.
- Double-check all connections and guarantee they’re safe earlier than using the motorbike.
Eradicating Previous Hand Grips
Earlier than putting in new hand grips in your Electra Glide Normal, you may have to take away the outdated ones. Here is an in depth information that can assist you by the method:
- Collect your instruments. You will want a flathead screwdriver, a pair of needle-nose pliers, and a razor blade or sharp knife.
- Take away the tip caps. Use the flathead screwdriver to pry off the tip caps on every hand grip.
- Find the wires. Beneath the tip caps, you may discover {the electrical} wires that join the hand grips to the motorbike’s electrical system. Disconnect the wires by unplugging them from their connectors.
- Reduce the adhesive. Use a razor blade or sharp knife to fastidiously reduce by the adhesive that’s holding the hand grips in place. You should definitely reduce slowly and punctiliously to keep away from damaging the handlebars.
- Take away the hand grips. As soon as the adhesive is reduce, it is best to have the ability to simply take away the hand grips from the handlebars. In the event that they’re nonetheless caught, you need to use the needle-nose pliers to softly pry them off.
| Supplies |
|---|
| Flathead screwdriver |
| Needle-nose pliers |
| Razor blade or sharp knife |
Cleansing Handlebar
It is very important clear the handlebar earlier than putting in the hand grips, to take away any filth or particles that would intervene with the set up.
Listed here are the steps on how you can clear the handlebar:
- Use a clear material and a few rubbing alcohol to wipe down the handlebar.
- Pay particular consideration to any areas which are significantly soiled or have any residue.
- Enable the handlebar to dry utterly earlier than continuing with the set up.
Listed here are some extra ideas for cleansing the handlebar:
- Use a light detergent. A light detergent will assist to take away filth and particles with out damaging the end of the handlebar.
- Keep away from utilizing abrasive cleaners. Abrasive cleaners can scratch the end of the handlebar.
- Rinse the handlebar totally. Make sure that to rinse the handlebar totally to take away the entire detergent.
- Dry the handlebar utterly. Enable the handlebar to dry utterly earlier than continuing with the set up.
Making use of Throttle Cable Lubricant
After putting in the left management and throttle housing, you are able to lubricate the throttle cable. This can assist guarantee easy and responsive throttle operation.
- Find the throttle cable adjustment barrel on the backside of the left management.
- Take away the throttle cable adjuster cap and apply a beneficiant quantity of throttle cable lubricant to the adjuster threads.
- Reinstall the adjuster cap and hand-tighten it.
- Lubricating the Throttle Cable (Detailed Information):
- Grasp the throttle grip and rotate it forwards and backwards a number of instances to unfold the lubricant all through the cable.
- Flip the handlebars totally to the left and proper whereas concurrently rotating the throttle to make sure the lubricant reaches all areas of the cable.
- Repeat this course of for a couple of minutes till the throttle motion turns into easy and easy.
- Wipe away any extra lubricant.
Notice: Use a high-quality throttle cable lubricant particularly designed for motorbike purposes. Lubricating the throttle cable frequently will assist extend its life and stop corrosion.
Putting in Throttle Aspect Hand Grip
Comply with these detailed steps to put in the throttle facet hand grip:
1. Preparation
Be sure that the ignition is turned off and the battery is disconnected.
2. Take away the Throttle Housing
Find the 2 screws holding the throttle housing in place and take away them.
3. Slide Off the Throttle Housing
Rigorously slide the throttle housing off the handlebar. Don’t twist or pull the throttle cable.
4. Substitute the Throttle Grip
Slide the outdated throttle grip off the throttle tube. Place the brand new grip on the tube and rotate it totally clockwise to lock it in place.
5. Reassemble the Throttle Aspect
Rigorously align the throttle housing with the handlebar and slide it again into place. Tighten the 2 screws securely.
Reattach the throttle and idle cables to the throttle housing.
Join the battery and activate the ignition.
Examine the throttle operation by twisting the grip and making certain it strikes easily and returns to the impartial place.
Securing Throttle Aspect Hand Grip
6. **Cross the throttle cable by the grip**: This step is essential to make sure correct performance of the throttle. Earlier than inserting the cable, barely lubricate it with an appropriate lubricant to reduce friction and promote easy operation.
Rigorously align the cable with the corresponding slots or guides inside the grip. Gently push the cable by till it reaches the opposite finish of the grip.
Be sure that the cable isn’t twisted or kinked throughout this course of. If vital, rotate or regulate the grip barely to facilitate the cable’s passage.
As soon as the cable is efficiently handed by, confirm its free motion by twisting the grip forwards and backwards. The throttle ought to function easily with none resistance or binding.
Lubricants |
Benefits |
|---|---|
| Lithium grease | Waterproof, high-temperature stability |
| Teflon lubricant | Low friction coefficient, corrosion resistance |
| Graphite powder | Dry lubricant, appropriate for high-heat purposes |
Putting in Clutch Aspect Hand Grip
1. Take away the Bar Finish Weight
Unscrew the bar finish weight utilizing a hex key. Guarantee to assist the handlebar to forestall it from rotating.
2. Pull Throttle Housing Away
Gently pull the throttle housing away from the handlebar to reveal the clutch cable.
3. Loosen Clutch Cable Adjuster
Find the clutch cable adjuster on the handlebars and loosen the locknut. Flip the adjuster to create slack within the clutch cable.
4. Take away Previous Hand Grip
Insert a flat-head screwdriver or a small pry bar into the hole between the handgrip and the handlebar. Rigorously pry the grip unfastened and take away it.
5. Clear Handlebar
Use a degreaser or rubbing alcohol to wash any filth or adhesive residue from the handlebar.
6. Set up New Hand Grip
Apply a small quantity of grip glue or hairspray to the handlebar and the within of the brand new handgrip. Slide the handgrip onto the handlebar and align it accurately.
7. Tighten Clutch Cable Adjuster
Alter the clutch cable adjuster to the correct stress. Pull the clutch lever totally in and ensure the adjuster screw touches the lever. Again off the adjuster screw barely till you are feeling slight resistance within the clutch lever. Lastly, tighten the locknut to safe the adjustment.
8. Reinstall Throttle Housing
Slide the throttle housing again onto the handlebars and guarantee it’s correctly seated.
9. Set up Bar Finish Weight
Screw the bar finish weight again into place and tighten it securely.
10. Take a look at Hand Grip
Function the clutch lever and throttle grip to make sure they’re functioning correctly.
Centering Hand Grips
As soon as the grips are put in, it’s essential to heart them. To do that:
- Use the marks on the within of the grips to align them with the middle of the handlebars.
- Tighten the grip bolts regularly and evenly, alternating between the 2 bolts till they’re cosy.
- Examine the alignment once more and make any vital changes.
- Tighten the grip bolts to the required torque (often round 7 ft-lbs).
- Reinstall the tip caps.
- Examine the grips for match and luxury. If they’re too unfastened or too tight, regulate the grip bolts accordingly.
- Wipe down the grips with a clear material to take away any fingerprints or filth.
- Begin your Electra Glide and benefit from the journey!
Ideas for Centering Hand Grips
* Use a degree to ensure the handlebars are degree earlier than putting in the grips.
* When you have bother getting the grips centered, attempt utilizing a small block of wooden or a rubber mallet to faucet them into place.
* Be affected person and take your time. Centering the grips correctly will be sure that they’re snug and protected to make use of.
Trimming Extra Grip Rubber
After the grips are totally seated, you may have to trim any extra grip rubber that extends past the handlebars. That is particularly essential for the throttle grip, as extra rubber can intervene with the operation of the throttle. Here is an in depth information to trimming extra grip rubber:
Earlier than You Begin:
- Collect the mandatory instruments: a pointy utility knife or razor blade, a material, and a small quantity of rubbing alcohol.
- Place the motorbike on a secure floor and safe it with a kickstand or heart stand.
- Clear the handlebar space and grip surfaces with rubbing alcohol to take away any filth or particles.
Step 1: Mark the Extra Rubber
Utilizing a pointy utility knife or razor blade, fastidiously rating a line across the extra rubber that extends past the handlebars. Make sure that the road is straight and exact.
Step 2: Reduce the Extra Rubber
Maintain the utility knife or razor blade perpendicular to the handlebars and reduce alongside the scored line. Apply mild stress and slide the blade easily to keep away from tearing or ragged edges.
Step 3: Deburr the Edges
As soon as the surplus rubber is eliminated, use the utility knife or razor blade to calmly deburr the perimeters of the grip rubber. This can take away any sharp or tough edges that could possibly be uncomfortable or trigger untimely put on.
Step 4: Easy the Grip Floor
Dampen a material with rubbing alcohol and gently rub it over the grip floor. This can assist to easy out any tough edges or imperfections left from the trimming course of.
Step 5: Examine and Re-Trim if Mandatory
Examine the trimmed grips to make sure that they’re flush with the handlebars and don’t intervene with the operation of the throttle. If vital, repeat the trimming course of to take away any remaining extra rubber.
| Security Tip: |
|---|
| Put on acceptable security gear, corresponding to security glasses and gloves, when utilizing sharp instruments. |
Ending Touches
10. Alter the Brake and Clutch Levers
Guarantee each levers are correctly positioned for optimum consolation and attain. Alter the levers to suit your hand dimension and using fashion. Tighten the locking nuts securely to forestall any motion or loosening throughout use.
Alter the clutch lever in order that it engages easily and releases with none extreme pressure. The brake lever needs to be positioned to offer ample braking energy with out inflicting hand pressure. Take note of the positioning of your fingers on the levers and make changes as wanted for optimum consolation and management.
|
Brake Lever: |
|
|
Clutch Lever: |
|
How one can Set up Hand Grips on an Electra Glide Normal
Putting in hand grips in your Electra Glide Normal is a comparatively easy and simple activity. Here is a step-by-step information that can assist you by the method:
- Collect the mandatory instruments. You’ll need a flathead and Phillips head screwdriver, a pair of pliers, and a utility knife.
- Take away the outdated hand grips. Use the flathead screwdriver to pry the perimeters of the outdated hand grips unfastened. As soon as they’re unfastened, use the pliers to drag them off the handlebars.
- Clear the handlebars. Use a clear material to wipe down the handlebars to take away any filth or particles.
- Apply a skinny layer of adhesive to the handlebars. Use a brush or your finger to use a skinny layer of adhesive to the within of the handlebars.
- Slide on the brand new hand grips. Slide the brand new hand grips onto the handlebars, ensuring to align them correctly.
- Tighten the screws. Tighten the screws on the underside of the hand grips utilizing the Phillips head screwdriver. Don’t overtighten the screws.
- Trim the surplus adhesive. Use the utility knife to trim any extra adhesive that will have seeped out from underneath the hand grips.
Folks Additionally Ask
How do I take away the throttle housing?
To take away the throttle housing, you will have to take away the 2 screws that maintain it in place. As soon as the screws are eliminated, you possibly can pull the throttle housing off the handlebars.
Can I set up any kind of hand grips on my Electra Glide Normal?
Sure, you possibly can set up any kind of hand grips in your Electra Glide Normal. Nonetheless, you could have to buy adapters if the hand grips you select don’t match the handlebars.
How typically ought to I substitute my hand grips?
Hand grips needs to be changed after they change into worn or broken. This can sometimes happen each 2-3 years, relying on how typically you journey your motorbike.
