Changing a heating component in a Samsung dryer can prevent the price of shopping for a brand new dryer or hiring an equipment restore technician. To switch the heating component, you may first want to collect the mandatory instruments and supplies, together with a brand new heating component, screwdriver, and pliers. After getting the mandatory gadgets, comply with these steps to switch the heating component in your Samsung dryer.
First, unplug the dryer from the facility outlet and take away the again panel of the dryer. Subsequent, find the heating component and disconnect the wires which can be hooked up to it. Then, take away the outdated heating component from the dryer. To put in the brand new heating component, merely insert it into the dryer and reconnect the wires. Lastly, substitute the again panel of the dryer and plug it again into the facility outlet. Your Samsung dryer ought to now be working correctly.
In case you are not assured in your potential to switch the heating component your self, it’s best to contact a professional equipment restore technician. A professional technician will be capable of rapidly and safely substitute the heating component in your Samsung dryer and get it working correctly once more.
Security Precautions
Earlier than embarking on the duty of changing the heating component in your Samsung dryer, it’s crucial to prioritize your security. Electrical energy and heating parts can pose important dangers if correct precautions should not taken. To make sure a secure and profitable restore, meticulously adhere to the next security measures:
1. Disconnect the Energy Supply
The primary and most vital step is to disconnect {the electrical} provide to your dryer. That is a necessary security measure to forestall any unintended electrical shocks or fires. Find the primary electrical panel in your house and swap off the circuit breaker or take away the fuse equivalent to the dryer. Confirm that the facility has certainly been disconnected by testing the dryer outlet with a voltage tester. Wait a couple of minutes to permit any residual electrical energy within the system to dissipate.
| Suggestions for Disconnecting the Energy Supply |
|---|
| – Establish the proper circuit breaker or fuse for the dryer. |
| – Swap off the corresponding circuit breaker or take away the fuse. |
| – Use a voltage tester to substantiate that the outlet is now not receiving energy. |
| – Enable ample time for the residual electrical energy to dissipate. |
Collect Needed Instruments and Supplies
Earlier than embarking on the restore, it is essential to collect the important instruments and supplies. Here is an in depth rundown of what you may want:
Supplies:
- New heating component
- Electrical tape
- Warmth-resistant gloves (non-obligatory)
Instruments:
| Instrument | Function |
|---|---|
| Phillips-head screwdriver | Take away the screws securing the entry panels and heating component |
| Torx screwdriver | Unscrew the bolts holding the heating component in place (some fashions) |
| Multimeter | Take a look at the continuity of the heating component (non-obligatory) |
| Pliers (non-obligatory) | Tighten or loosen nuts or bolts |
| Protecting goggles (non-obligatory) | Shield eyes from unfastened particles |
Further Supplies:
Whereas not strictly essential, sure supplies could make the restore course of smoother:
- Flashlight: Illuminate the work space, particularly in dimly lit areas
- Store towels or rags: Clear up any particles or spills
- Digital camera: Doc the disassembly course of for simpler reassembly
- Warmth gun (non-obligatory): Soften outdated adhesive or pace up evaporation of moisture
- Soldering iron (non-obligatory): Restore broken wires or safe new connections
Find and Take away the Rear Panel
Unplug the dryer and transfer it away from the wall.
For security functions, unplug your dryer from the facility outlet earlier than beginning any repairs. It will even be greatest to drag the dryer away from the wall to offer your self ample area to work.
Find the screws holding the rear panel in place.
Figuring out the screws that maintain the rear panel of the dryer is essential. These screws are sometimes situated across the perimeter of the panel, and their place might fluctuate barely relying on the dryer mannequin. After getting recognized the screws, proceed to the following step.
Take away the screws and thoroughly elevate off the rear panel.
After getting situated the screws, use a screwdriver to take away them. Watch out to not strip the screws or harm the rear panel when eradicating them. After eradicating all of the screws, rigorously elevate the rear panel off the dryer. Observe that the rear panel could also be barely heavy, so remember to assist it with one hand whereas eradicating the screws with the opposite.
Disconnect Current Heating Factor
**Step 1: Unplug the Dryer**
Earlier than engaged on the dryer, disconnect it from the facility provide by unplugging it from the wall outlet.
**Step 2: Take away the Again Panel**
Find the screws on the again panel of the dryer and take away them utilizing a screwdriver. Fastidiously elevate and take away the again panel to reveal the internal parts.
**Step 3: Disconnect Wires**
Establish the 2 wires linked to the heating component terminals. Gently pull the wire connectors off the terminals. Make observe of which wire goes to which terminal for future reference.
**Step 4: Take away the Heating Factor**
The heating component is held in place by two screws or bolts. Use a wrench or socket to loosen and take away these fasteners. Fastidiously slide the heating component out of its housing. Be conscious of sharp edges and keep away from touching the component along with your naked palms.
| Screw/Bolt Location | Removing Technique |
|---|---|
| Prime of the housing | Loosen with a wrench or socket |
| Backside of the housing | Take away with a wrench or socket |
**Step 5: Examine the Heating Factor**
Visually examine the heating component for any harm or corrosion. If the component is broken, it’s going to should be changed earlier than reassembling the dryer.
Take away Previous Heating Factor
5. Disconnect the heating component from the facility provide.
| Kind of Dryer | Steps |
|---|---|
| Gasoline Dryer |
Shut off the gasoline provide to the dryer earlier than continuing. |
| Electrical Dryer |
Unplug the dryer from the facility outlet and switch off the circuit breaker or fuse for the dryer circuit |
6. Take away the screws that maintain the heating component in place.
7. Unclip the wire terminals from the heating component.
8. Pull the heating component out of the dryer.
Set up New Heating Factor
Security Precautions
Earlier than starting any work, unplug your dryer and disconnect the facility supply. Make sure that the machine is cool to the contact.
Eradicating the Previous Heating Factor
- Take away the entrance panel of the dryer by unscrewing the screws on the high and pulling it ahead.
- Find the entry panel on the entrance of the dryer’s drum. Take away the screws and pull it open.
- Pull the outdated heating component unit in the direction of you to disconnect the wires.
- Unplug the wires from {the electrical} terminals and take away the outdated heating component.
Putting in the New Heating Factor
- Insert the brand new heating component unit into the opening within the drum.
- Join the wires to {the electrical} terminals. Make sure that the connections are safe.
- Push the heating component unit again into place and safe it with the screws.
- Reattach the entry panel and the entrance panel of the dryer.
- Plug the dryer again into the facility outlet and switch it on to check the brand new heating component.
Suggestions for Troubleshooting
| Drawback | Answer |
|---|---|
| Dryer not heating | Examine the facility provide. Examine the wires and connections to the heating component. Take a look at the heating component with a multimeter. |
| Dryer overheating | Unplug the dryer and let it quiet down. Clear the lint filter and exhaust vent. Examine the thermostat and temperature sensor. |
Reconnect Electrical Wires
Now it is time to reconnect {the electrical} wires to the heating component. Make sure you match the wires to the proper terminals on the component. Sometimes, the pink wire will connect with the left terminal and the white wire will connect with the best terminal. Nevertheless, check with your dryer’s particular wiring diagram to substantiate.
Tighten the screws on the terminals securely utilizing a screwdriver. Make sure that the wires are making good contact with the terminals to forestall any unfastened connections that would trigger arcing or different electrical points.
As soon as the wires are linked, tuck them again into the insulation across the heating component. This may assist to guard the wires from warmth harm and hold the within of the dryer tidy.
Wiring Diagram
For fast reference, here’s a desk with a normal wiring diagram for many Samsung dryers:
| Wire Shade | Terminal |
|---|---|
| Pink | Left Terminal |
| White | Proper Terminal |
Once more, double-check your dryer’s particular wiring diagram to make sure accuracy earlier than making any connections.
Exchange Rear Panel
Now that the screws are eliminated, elevate the rear panel up from the underside and pull it in the direction of you to detach it from the dryer. Watch out to not harm any wires or parts as you do that.
As soon as the rear panel is eliminated, you’ll have entry to the heating component. The heating component is situated on the backside of the dryer, behind the drum. It’s held in place by two screws.
Step 8: Take away the Heating Factor’s Wiring
Earlier than eradicating the heating component, you might want to disconnect its wiring. The heating component has two wires linked to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating component’s terminals.
As soon as the wires are disconnected, you’ll be able to take away the heating component. Use a screwdriver to take away the 2 screws that maintain the heating component in place. As soon as the screws are eliminated, the heating component may be pulled out of the dryer.
| Step 6: Find the Heating Factor | The heating component is situated on the backside of the dryer, behind the drum. It’s held in place by two screws. |
| Step 7: Disconnect the Heating Factor’s Wiring | Earlier than eradicating the heating component, you might want to disconnect its wiring. The heating component has two wires linked to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating component’s terminals. |
| Step 8: Take away the Heating Factor | As soon as the wires are disconnected, you’ll be able to take away the heating component. Use a screwdriver to take away the 2 screws that maintain the heating component in place. As soon as the screws are eliminated, the heating component may be pulled out of the dryer. |
As soon as the outdated heating component is eliminated, you’ll be able to substitute it with the brand new one. Insert the brand new heating component into the dryer and safe it with the 2 screws. Make sure you join the wires to the heating component’s terminals within the right order: black wire to black terminal, white wire to white terminal.
As soon as the brand new heating component is put in, you’ll be able to reattach the rear panel to the dryer. Safe the rear panel with the screws that you simply eliminated earlier.
Take a look at the Dryer
After getting changed the heating component, you will need to take a look at the dryer to verify it’s working correctly. Listed below are the steps on take a look at the dryer:
| Step | Motion |
|---|---|
| 1 | Ensure the dryer is plugged into an outlet and that the facility swap is turned on. |
| 2 | Open the dryer door and place a moist towel inside. |
| 3 | Shut the dryer door and choose the “Regular” or “Timed Dry” cycle. |
| 4 | Press the “Begin” button to begin the dryer. |
| 5 | Let the dryer run for a couple of minutes to see if the towel will get heat. |
| 6 | If the towel will get heat, then the heating component is working correctly. |
| 7 | If the towel doesn’t get heat, then there could also be an issue with the heating component or different parts of the dryer. |
In case you are having issues along with your dryer, it’s best to contact a professional equipment restore technician for help.
Security Precautions Earlier than Beginning:
1. Unplug the dryer from the facility outlet and permit it to chill utterly.
2. Put on gloves to guard your palms from sharp edges.
3. Collect all essential instruments and components earlier than beginning.
Checking the Heating Factor:
1. Take away the again panel of the dryer by unscrewing the screws across the perimeter.
2. Find the heating component, which is often an oblong metallic field with two wires linked to it.
3. Unplug the wires from the heating component utilizing needle-nose pliers.
Eradicating the Heating Factor:
1. Unscrew the nuts holding the heating component in place.
2. Fastidiously elevate the heating component out of the dryer cupboard.
Putting in the New Heating Factor:
1. Place the brand new heating component into the dryer cupboard.
2. Tighten the nuts holding the heating component in place.
3. Join the wires to the heating component.
Troubleshooting Suggestions
1. If the dryer nonetheless doesn’t warmth, test the thermal fuse.
2. If the thermal fuse is blown, substitute it.
3. If the heating component shouldn’t be getting energy, test the wiring.
4. If the wiring is broken, restore or substitute it.
5. If the dryer continues to be not heating, contact a professional equipment restore technician.
Further Troubleshooting Suggestions:
| Potential Trigger | Answer |
|---|---|
| Unfastened belt | Modify or substitute the belt |
| Vent blockage | Clear the dryer vent |
| Defective thermostat | Exchange the thermostat |
| Defective relay | Exchange the relay |
| Defective management board | Exchange the management board |
7. If the dryer is making a loud noise, test the drum bearings.
8. If the drum bearings are worn, substitute them.
9. If the dryer is shaking excessively, test the shock absorbers.
10. If the shock absorbers are worn, substitute them.
Learn how to Set up a Heating Factor in a Samsung Dryer
Changing the heating component in a Samsung dryer is a comparatively easy activity that may be accomplished in about an hour. Nevertheless, you will need to take security precautions and comply with the directions rigorously to keep away from harm or harm to the dryer.
Supplies wanted:
- New heating component
- Screwdriver
- Wrench
- Security glasses
- Gloves
Directions:
- Unplug the dryer from the facility outlet.
- Placed on security glasses and gloves.
- Take away the again panel of the dryer by unscrewing the screws that maintain it in place.
- Find the heating component, which is normally situated on the backside of the dryer.
- Disconnect the wires from the heating component.
- Unscrew the bolts that maintain the heating component in place.
- Raise the heating component out of the dryer.
- Place the brand new heating component into the dryer.
- Screw within the bolts to safe the heating component in place.
- Join the wires to the heating component.
- Exchange the again panel of the dryer.
- Plug the dryer again into the facility outlet.
