Are you looking for to take away your Ring Doorbell Professional to interchange it with a brand new one, relocate it to a distinct spot, or for another motive? Eradicating a Ring Doorbell Professional is a comparatively easy course of that may be accomplished in just a few steps. Whether or not you are an skilled DIY fanatic or a first-timer, this information will give you clear directions and useful ideas to make sure a profitable elimination. After getting eliminated your Ring Doorbell Professional, you may proceed with the mandatory actions, corresponding to putting in a brand new doorbell or storing it for future use.
Earlier than you start the elimination course of, it’s essential to assemble the mandatory instruments. You have to a Philips head screwdriver, a small flathead screwdriver, and a pair of needle-nose pliers. Moreover, in case your Ring Doorbell Professional is at the moment powered by batteries, you will want to take away them. After getting all the mandatory instruments and supplies, you may proceed with the next steps: 1. Take away the faceplate by inserting the small flathead screwdriver into the notch on the backside of the faceplate and gently prying it off. 2. Use the Philips head screwdriver to take away the 2 screws that safe the mounting bracket to the wall.
3. Fastidiously pull the Ring Doorbell Professional straight in direction of you, disconnecting it from the mounting bracket. 4. In case your Ring Doorbell Professional is wired, disconnect the wires from the terminals on the again of the machine. 5. Take away the mounting bracket from the wall by unscrewing the 2 screws that safe it. After getting accomplished these steps, your Ring Doorbell Professional will likely be efficiently faraway from the wall. Now you can proceed with the subsequent steps, corresponding to putting in a brand new doorbell or storing the Ring Doorbell Professional for future use. Keep in mind to deal with the machine with care all through the elimination course of to keep away from any injury.
Safely Disconnect the Energy
Earlier than you start:
It is essential to take correct precautions earlier than disconnecting the ability to your Ring Doorbell Professional. Comply with these security tricks to keep away from any potential hazards:
- Establish the primary energy supply: Decide whether or not your Doorbell Professional is powered by batteries or a wired connection. If it is wired, you will have to find the circuit breaker or fuse field that provides energy to the doorbell.
- Flip off energy on the primary breaker: As soon as you’ve got recognized the ability supply, flip off the ability to the circuit that feeds your doorbell. This may guarantee there is not any electrical present flowing via the machine once you disconnect it.
- Double-check for energy: Use a multimeter or voltage tester to substantiate that the ability to the doorbell has been efficiently disconnected. This will provide you with peace of thoughts and stop any electrical accidents.
Further Precautions:
| State of affairs | Precautions |
|---|---|
| Battery-powered Doorbell Professional | Take away the batteries from the machine earlier than disconnecting it. |
| Wired Doorbell Professional | Flip off the ability on the circuit breaker or fuse field and disconnect the doorbell’s wires from {the electrical} junction field. |
| Shared Energy Supply | In case your Doorbell Professional shares an influence supply with different gadgets, disconnect all linked gadgets earlier than turning off the ability. |
Keep in mind, security ought to all the time be your high precedence when working with electrical gadgets. By following these precautions, you may guarantee a protected and profitable elimination of your Ring Doorbell Professional.
Take away the Faceplate
To take away the faceplate out of your Ring Doorbell Professional, observe these steps:
- Take away the screw. Use a Phillips screwdriver to take away the one screw situated within the backside middle of the faceplate.
- Pry the faceplate off. Fastidiously pry the faceplate off the doorbell base utilizing a plastic pry instrument or a flat-head screwdriver. Keep away from utilizing extreme pressure, as you might injury the machine or surrounding surfaces.
- Disconnect the doorbell wire (elective). If you happen to’re planning to maneuver your doorbell to a brand new location, you will have to disconnect the doorbell wire. To do that, merely push down on the wire connector tab and pull the wire out.
Further Suggestions for Eradicating the Faceplate Safely
Listed below are some extra ideas for eradicating the faceplate of your Ring Doorbell Professional safely and effectively:
- Guarantee that you’ve the right instruments for the job, corresponding to a Phillips screwdriver and a plastic pry instrument or flat-head screwdriver.
- Apply light stress when prying the faceplate off to keep away from damaging the machine or surrounding surfaces.
- If you happen to encounter any resistance when eradicating the faceplate, cease and examine the realm for any obstacles or obstructions.
- If you happen to’re disconnecting the doorbell wire, ensure that to push down on the wire connector tab firmly to launch the wire.
| Step | Motion |
|---|---|
| 1 | Find and take away the screw utilizing a Phillips screwdriver. |
| 2 | Use a plastic pry instrument or flat-head screwdriver to rigorously pry off the faceplate. |
| 3 (elective) | If transferring the doorbell, disconnect the doorbell wire by urgent down on the wire connector tab and pulling out the wire. |
Detach the Mounting Bracket
Step one in eradicating your Ring Doorbell Professional is to detach the mounting bracket. To do that, you will want to take away the 2 screws which are situated on the underside of the bracket. As soon as the screws are eliminated, you may gently pull the bracket away from the wall.
If you happen to discover that the bracket is caught, you should utilize a screwdriver or a pair of pliers to softly pry it unfastened. Watch out to not injury the bracket or the wall when doing this.
As soon as the bracket is indifferent, you will want to disconnect the wires which are linked to the doorbell. To do that, merely use your fingers to pinch the terminals on the again of the doorbell and pull the wires out.
Here’s a desk that summarizes the steps concerned in detaching the mounting bracket:
| Step | Motion |
|—|—|
| 1 | Take away the 2 screws which are situated on the underside of the bracket. |
| 2 | Gently pull the bracket away from the wall. |
| 3 | If the bracket is caught, use a screwdriver or a pair of pliers to softly pry it unfastened. |
| 4 | Disconnect the wires which are linked to the doorbell. |
Disassemble the Energy Equipment
The Energy Equipment is the a part of the Ring Doorbell Professional that connects the doorbell to your property’s electrical system. To take away the Ring Doorbell Professional, that you must first disassemble the Energy Equipment that connects the doorbell to the wiring of your property. This is do it:
- Flip off the ability to your doorbell on the circuit breaker or fuse field.
- Take away the 2 screws that maintain the faceplate of the Energy Equipment in place.
- Pull the faceplate straight out from the wall.
- Contained in the Energy Equipment, you will notice 4 wires:
- As soon as the wires are disconnected, you may take away the Energy Equipment from the wall.
| Wire | Description |
|---|---|
| White | Impartial wire |
| Black | Sizzling wire |
| Inexperienced | Floor wire |
| Pink | Energy wire |
Disconnect the wires from the Energy Equipment by loosening the screws on the wire terminals. Make sure that to recollect which wire was linked to which terminal.
Uninstall the Electrical Wires
Step 1: Flip off the ability to your Ring Doorbell Professional on the circuit breaker or fuse field. This can be a essential security measure to stop electrical shocks.
Step 2: Take away the faceplate of your Ring Doorbell Professional by unscrewing the 2 safety screws situated on the backside of the machine.
Step 3: Disconnect the wires from the Ring Doorbell Professional terminals. Word the positions of the wires (often labeled “FRONT” and “REAR”) so you may reconnect them appropriately later.
Step 4: Use a screwdriver or wire strippers to loosen the terminal screws and thoroughly take away the wires.
Step 5: Pull the wires gently out of the wall to create some slack. You might want to make use of a pair of needle-nose pliers to grip the wires securely.
| Rear | Entrance |
|---|---|
| White wire (-) | Black wire (+) |
Step 6: Tape the ends of the wires collectively utilizing electrical tape to stop them from touching and creating a brief circuit.
Step 7: Tuck the wires again into the wall and safe them with electrical tape or wire nuts.
Step 8: Restore energy to your Ring Doorbell Professional by turning the circuit breaker or fuse again on.
Take away the Chime Equipment (If Put in)
If you happen to’ve put in a Ring Doorbell Professional with a chime package, you will have to take away it earlier than continuing. This is how:
Step 1: Find the chime package.
It is usually mounted on a wall close to an present doorbell chime.
Step 2: Flip off energy to the chime package.
Flip the breaker that controls the chime package’s circuit or take away the fuse.
Step 3: Disconnect the chime package from the wall.
Use a screwdriver to take away the screws holding it in place.
Step 4: Disconnect the wires from the chime package.
Take an image of the wiring configuration earlier than disconnecting any wires. This may enable you to rewire the chime package later if wanted.
Step 5: Take away the chime package from the wall.
As soon as the wires are disconnected, you may pull the chime package away from the wall and take away it fully.
Step 6: Cap the uncovered wires.
Utilizing electrical tape or wire nuts, cap the uncovered wires on the wall and on the chime package. This may forestall electrical shocks and quick circuits.
| Wire Coloration | Connection |
|---|---|
| Pink | Transformer terminal (constructive) |
| Black | Transformer terminal (adverse) |
| White | Entrance doorbell button |
| Yellow | Rear doorbell button (if relevant) |
Reset the Ring Doorbell Professional
Step 1: Take away the Faceplate
Gently pry off the faceplate protecting the doorbell’s buttons and digicam.
Step 2: Find the Reset Button
Contained in the doorbell, discover the small, black reset button situated close to the underside.
Step 3: Insert a Pin
Use a small pin or paperclip to softly press and maintain the reset button for 15 seconds.
Step 4: Launch the Button
After 15 seconds, launch the reset button.
Step 5: Look ahead to the Blue Ring
The doorbell will flash a blue ring across the button to point it’s resetting.
Step 6: Reinstall the Faceplate
As soon as the blue ring has stopped flashing, substitute the faceplate over the doorbell.
Step 7: Reconfigure the Doorbell
a) Open the Ring App
Launch the Ring app in your smartphone and log in to your account.
b) Choose the Doorbell
Select the Ring Doorbell Professional you wish to reconfigure from the checklist of gadgets.
c) Comply with the Prompts
Comply with the on-screen directions within the app to reconnect your doorbell to Wi-Fi and full the setup course of.
Confirm Profitable Elimination
After getting accomplished the steps above, it is vital to confirm that the Ring Doorbell Professional has been efficiently eliminated. This is how:
Checking the Ring App
Open the Ring app in your cell machine. If the Ring Doorbell Professional has been eliminated efficiently, it should not seem within the checklist of gadgets.
Checking Your Gateway
If in case you have a Ring Chime Professional or Ring Chime, it should present a blue mild when the Ring Doorbell Professional is linked. If the Ring Doorbell Professional has been eliminated efficiently, the blue mild on the Gateway will flip off.
Checking for Bodily Disconnection
Go to the place the Ring Doorbell Professional was put in. If it has been eliminated efficiently, the doorbell will not be bodily linked to the wiring.
Troubleshooting
If you happen to’ve adopted the steps above however the Ring Doorbell Professional continues to be showing within the Ring app or the Gateway continues to be exhibiting a blue mild, strive the next:
- Just remember to have accomplished all of the steps within the elimination course of.
- Restart the Ring Doorbell Professional by urgent the orange button on the again of the machine.
- Restart the Ring app in your cell machine.
- Contact Ring assist for additional help.
Clear the Mounting Space
Earlier than eradicating your Ring Doorbell Professional, it is vital to wash the mounting space to stop any residue or dust from affecting the set up course of. This is clear it successfully:
1. Collect the Mandatory Instruments
You may want a mushy fabric, rubbing alcohol, and a screwdriver or drill.
2. Flip Off the Energy
Change off the breaker or fuse that powers the doorbell to make sure security.
3. Take away the Faceplate
Use a screwdriver to unscrew the 2 screws on the backside of the faceplate and carry it off the bottom.
4. Clear the Base
Wipe down the bottom of the doorbell with a mushy fabric dampened with rubbing alcohol. Make sure that to take away any dust or particles.
5. Clear the Mounting Floor
Utilizing a humid fabric, wipe down the realm the place the doorbell was mounted to take away any dust or residue. Guarantee it is fully dry earlier than persevering with.
6. Take away the Mounting Plate
Unscrew the 4 screws that safe the mounting plate to the mounting floor. Fastidiously carry the plate off.
7. Clear the Screws
Wipe down the screws with rubbing alcohol to take away any dust or particles.
8. Examine the Seal
Test the rubber seal across the mounting plate. If it is broken or worn, substitute it earlier than putting in the brand new doorbell.
9. Clear the Wires
If you happen to’re changing the doorbell with a wired mannequin, clear the wires utilizing rubbing alcohol. Guarantee they’re freed from dust or corrosion. It’s also possible to use a wire brush to take away any cussed residue or oxidation.
| Supplies | Utilization |
|---|---|
| Tender fabric | Wiping surfaces |
| Rubbing alcohol | Cleansing surfaces and wires |
| Screwdriver or drill | Eradicating screws |
Safe the Gap or Wires
As soon as the doorbell is disconnected, that you must safe the opening the place it was mounted. If you happen to do not, water, bugs, or different particles can enter your property via the opening. There are just a few methods to do that, relying on the kind of floor the doorbell was mounted on.
If the doorbell was mounted on brick or concrete:
- Fill the opening with a silicone or polyurethane caulk utilizing a caulk gun.
- Easy the caulk along with your finger or a putty knife.
- Permit the caulk to dry fully, which can take a number of hours or days, relying on the kind of caulk used.
If the doorbell was mounted on wooden:
- Reduce a small piece of wooden to suit over the opening.
- Glue or nail the wooden piece into place.
- Paint or stain the wooden piece to match the encircling space.
If the doorbell was mounted on vinyl siding:
- Take away the siding panel that the doorbell was mounted on.
- Reduce a bit of scrap siding to suit over the opening.
- Glue or nail the scrap siding into place.
- Reinstall the siding panel.
If the doorbell was mounted on a floor apart from brick, concrete, wooden, or vinyl siding:
- Seek the advice of with a house enchancment skilled for recommendation on the easiest way to safe the opening.
Along with securing the opening, you additionally have to deal with the wires that have been linked to the doorbell. If the wires will not be correctly insulated, they may change into a hearth hazard. Reduce the wires near the doorbell after which wrap them with electrical tape or cowl them with wire nuts.
The best way to Take away a Ring Doorbell Professional
To take away a Ring Doorbell Professional, observe these steps:
1.
Flip off the ability to your doorbell by flipping the breaker or eradicating the fuse.
2.
Take away the faceplate by unscrewing the 2 screws on the backside.
3.
Disconnect the wires from the terminals on the again of the doorbell.
4.
Take away the 2 screws which are holding the doorbell in place.
5.
Pull the doorbell straight out of the wall.
Folks Additionally Ask About Eradicating a Ring Doorbell Professional
The best way to take away a Ring Doorbell Professional that’s hardwired?
In case your Ring Doorbell Professional is hardwired, you will want to disconnect the wires from the terminals on the again of the doorbell earlier than you may take away it. To do that, use a small screwdriver to loosen the screws on the terminals after which pull the wires off.
The best way to take away a Ring Doorbell Professional that’s battery-powered?
In case your Ring Doorbell Professional is battery-powered, you will want to take away the battery earlier than you may take away the doorbell. To do that, use a small screwdriver to loosen the screw on the underside of the doorbell after which pull the battery out.
