Changing a tub spout diverter is a simple job that may be accomplished in a couple of minutes with the precise instruments and slightly know-how. This is what you will must do.
First, you will want to collect your instruments. You will want a screwdriver, a pair of pliers, and a brand new diverter. Upon getting your instruments, you possibly can start the method of changing the diverter. To do that, you will first want to show off the water provide to the bathtub. As soon as the water is turned off, you possibly can take away the previous diverter by unscrewing it with the screwdriver. As soon as the previous diverter is eliminated, you possibly can screw on the brand new diverter. Lastly, you possibly can flip the water provide again on and take a look at the brand new diverter.
Most spouts have a diverter that directs water to the showerhead or tub spout. Over time, these diverters change into worn and might begin to leak. In case your bathtub diverter is leaking, it is necessary to switch it as quickly as potential to keep away from water injury. Changing a tub diverter is a comparatively straightforward DIY mission that may be accomplished in just a few steps. First, you will want to collect your instruments. You will want a screwdriver, a pair of pliers, and a brand new diverter. Upon getting your instruments, you possibly can start the method of changing the diverter.
Figuring out the Bathtub Spout Diverter
The bath spout diverter is a small however important element that lets you swap between the tub spout and the hand-held showerhead. It’s usually positioned on the base of the spout, and it might be product of plastic, metallic, or rubber. The diverter could also be a easy lever or knob, or it might be a extra complicated mechanism that requires you to press a button or flip a dial. In case your bathtub spout diverter isn’t working correctly, you could want to switch it.
There are just a few several types of bathtub spout diverters, so you will need to establish the kind you’ve got earlier than you buy a substitute. The commonest kind of diverter is the push-button diverter. One of these diverter has a small button that you simply press to modify between the spout and the showerhead. One other widespread kind of diverter is the lever diverter. One of these diverter has a lever that you simply transfer to modify between the spout and the showerhead.
If you’re unsure what kind of tub spout diverter you’ve got, you possibly can seek the advice of your bathtub’s proprietor’s guide or contact the producer. Upon getting recognized the kind of diverter you’ve got, you should purchase a substitute at your native ironmongery store or house enchancment heart.
Draining the Bathtub and Water Traces
Earlier than you start engaged on changing the spout diverter, it is necessary to empty the tub and switch off the water provide. This is how you can do it:
Drain the Bathtub
1. Find the drain plug on the backside of the tub and take away it.
2. Permit the water to empty out fully.
3. Clear the drain opening to take away any hair or particles that will have amassed.
4. Change the drain plug.
Flip off the Water Provide
1. Find the 2 water provide valves beneath the sink. These valves usually have handles labeled “scorching” and “chilly.”
2. Flip the handles clockwise to shut each valves, shutting off the water provide to the tub.
3. Open the tub faucet to launch any remaining water within the strains.
Establish and Flip off the Diverter Cease Valve
Some bathtubs have a diverter cease valve that must be turned off individually. This valve is often positioned behind the tub faucet, accessible via a small entry panel or behind a detachable cowl.
1. Find the diverter cease valve. It is usually a small, quarter-turn valve with a deal with or knob.
2. Flip the deal with or knob clockwise to shut the valve, stopping the stream of water to the diverter.
| Step | Motion |
|---|---|
| 1 | Find the drain plug on the backside of the tub and take away it. |
| 2 | Permit the water to empty out fully. |
| 3 | Clear the drain opening to take away any hair or particles that will have amassed. |
| 4 | Change the drain plug. |
| 5 | Find the 2 water provide valves beneath the sink. |
| 6 | Flip the handles clockwise to shut each valves, shutting off the water provide to the tub. |
| 7 | Open the tub faucet to launch any remaining water within the strains. |
| 8 | Find the diverter cease valve behind the tub faucet. |
| 9 | Flip the deal with or knob clockwise to shut the valve, stopping the stream of water to the diverter. |
Eradicating the Current Diverter
To start the substitute course of, you will must take away the present diverter. This is an in depth information that will help you do it safely and effectively:
1. Shut Off the Water Provide
Find the shut-off valves beneath the sink or in a close-by utility closet. Flip them clockwise to fully shut off the water provide to the tub.
2. Take away the Escutcheon Plate
The escutcheon plate is the ornamental plate that surrounds the diverter deal with. Use a screwdriver to take away the screws securing it in place. As soon as the screws are out, gently pull the escutcheon plate off.
3. Unscrew the Deal with
To unscrew the diverter deal with, merely rotate it counterclockwise. If the deal with is caught, you need to use a pair of pliers to grip it firmly and apply light drive.
4. Take away the Diverter Meeting
This step requires a bit extra warning, because the diverter meeting is commonly secured in place by a spring-loaded clip. This is how you can proceed:
- Fastidiously insert a flat-head screwdriver or choose into the small gap positioned on the facet of the diverter meeting.
- Push the clip inward and maintain it towards the spring’s stress.
- Use your different hand to softly pull the diverter meeting straight out. Watch out to not drive it.
- As soon as the meeting is disengaged from the clip, grip it firmly and pull it out fully.
With the present diverter eliminated, now you can proceed to the following step of putting in the brand new one.
Putting in the New Diverter
1. **Take away the previous diverter**. Take away the set screw or cap from the face of the diverter, then pull the deal with away from the spout. The diverter ought to now slide out of the spout.
2. **Clear the spout**. As soon as the previous diverter is eliminated, use a fabric to scrub the within of the spout, eradicating any filth or particles that will have amassed.
3. **Apply plumber’s putty**. Roll out a skinny rope of plumber’s putty and apply it across the base of the brand new diverter.
4. **Insert the brand new diverter**. Slide the brand new diverter into the spout, guaranteeing that the plumber’s putty makes a seal between the diverter and the spout.
5. **Set up the deal with**. Slide the deal with over the diverter and safe it with the set screw or cap. Watch out to not overtighten the screw, as this might injury the diverter.
6. **Check the diverter**. Activate the water and verify that the diverter is working correctly, directing the water stream as desired. If any leaks happen, tighten the set screw or cap till the leak stops.
Troubleshooting Suggestions
| Downside | Resolution |
|---|---|
| Leaking diverter | Tighten the set screw or cap. If the leak persists, change the diverter. |
| Water not flowing via diverter | Test that the diverter is correctly put in and that the plumber’s putty is making a seal. If the difficulty persists, change the diverter. |
| Diverter caught | Apply penetrating oil to the set screw or cap and permit it to take a seat for a couple of minutes. Then, attempt to loosen the screw or cap. If the diverter remains to be caught, change it. |
Reattaching the Deal with and Escutcheon
6. Reattaching the Deal with and Escutcheon:
- Place the escutcheon or trim plate over the valve physique.
- Align the deal with with the valve stem and slide it onto the stem till it’s cosy.
- Tighten the deal with set screw.
- Activate the water to verify for any leaks.
- If there aren’t any leaks, your bathtub spout diverter substitute is full.
| Instruments You will Want |
|---|
| Adjustable wrench |
| Phillips head screwdriver |
| Flat head screwdriver |
| Pliers |
| Putty knife |
| Flashlight |
| Substitute diverter |
Opening the Water Traces
Earlier than changing the diverter, flip off the water provide to the bathtub utilizing the shut-off valves positioned under the sink or behind the bathtub. Open the tub faucet to launch any remaining water stress. Use a wrench to disconnect the water provide strains from the previous diverter. Watch out to not injury the pipes.
Testing the Diverter
As soon as the brand new diverter is put in, activate the water provide and verify for leaks. Modify the diverter lever to make sure it easily switches between the showerhead and tub spout. For those who discover any leaks or improper operation, repeat the set up course of or contact an expert plumber for help.
Detailed Step-by-Step Directions for Testing the Diverter
1. Activate the water provide to the bathtub utilizing the shut-off valves.
2. Open the tub faucet and permit water to stream for a couple of minutes to clear the strains of any air.
3. Modify the diverter lever to the showerhead place and verify for leaks on the diverter and the showerhead connection.
4. Change the diverter lever to the bathtub spout place and verify for leaks on the diverter and the bathtub spout connection.
5. Repeat steps 3 and 4 a number of instances to make sure the diverter is working easily and with none leaks.
6. For those who discover any leaks or improper operation, confer with the troubleshooting information within the person guide or contact an expert plumber.
7. As soon as you’re glad with the efficiency of the diverter, depart the water working for a couple of minutes to verify for any persistent leaks. If no leaks are detected, you’ve got efficiently changed the tub spout diverter.
Troubleshooting Widespread Diverter Points
1. Diverter doesn’t swap
The commonest reason behind a diverter not switching is a buildup of mineral deposits or particles. To repair this, take away the diverter and soak it in a vinegar resolution for a number of hours. Then, use a toothbrush or small brush to take away any remaining deposits. If the diverter nonetheless doesn’t swap, it might have to be changed.
2. Diverter leaks
A leaking diverter could be attributable to a worn-out washer or O-ring. To repair this, take away the diverter and change the washer or O-ring. If the leak persists, the diverter might have to be changed.
3. Water stress is low
Low water stress could be attributable to a clogged diverter. To repair this, take away the diverter and clear it with a vinegar resolution. If the water stress remains to be low, the diverter might have to be changed.
4. Diverter is tough to show
A difficult-to-turn diverter could be attributable to a buildup of mineral deposits or corrosion. To repair this, take away the diverter and soak it in a vinegar resolution for a number of hours. Then, use a toothbrush or small brush to take away any remaining deposits. If the diverter remains to be tough to show, it might have to be changed.
5. Diverter deal with is unfastened
A unfastened diverter deal with could be attributable to a worn-out set screw. To repair this, tighten the set screw with a screwdriver. If the deal with remains to be unfastened, the diverter might have to be changed.
6. Diverter isn’t seated correctly
An improperly seated diverter may cause leaks or stop the diverter from switching. To repair this, take away the diverter and reinsert it, ensuring that it’s seated correctly.
7. Diverter is damaged
A damaged diverter will have to be changed. To exchange a diverter, you’ll need to take away the previous diverter and set up the brand new diverter. Directions for changing a diverter will fluctuate relying on the kind of diverter you’ve got.
8. Deal with doesn’t transfer easily
The deal with could also be tough to maneuver if the diverter isn’t correctly lubricated. To lubricate the diverter, apply a small quantity of petroleum jelly to the transferring elements. If the deal with nonetheless doesn’t transfer easily, the diverter might have to be changed.
Sustaining and Cleansing the Bathtub Spout Diverter
Common upkeep and cleansing of the tub spout diverter can lengthen its lifespan and forestall leaks. Observe these steps to maintain your diverter in good situation:
Test the diverter for any injury or leaks each few months. Search for cracks, rust, or unfastened connections.
Use a gentle cleaner and a delicate fabric to scrub the diverter’s deal with and spout. Keep away from utilizing abrasive cleaners or metal wool as they’ll injury the end.
Periodically, apply just a few drops of silicone lubricant to the diverter’s transferring elements. This can stop them from sticking and guarantee easy operation.
The diverter’s washer is a small rubber or plastic disc that creates a seal between the diverter and the spout. Examine the washer for injury or put on and change it if mandatory.
Mineral buildup can clog the diverter’så éšéé. To take away it, soak the diverter in an answer of white vinegar and water for a number of hours. Then, use a delicate brush to softly scrub away any remaining buildup.
For a extra thorough cleansing, you possibly can disassemble the diverter. Observe the producer’s directions rigorously to keep away from damaging the diverter. As soon as disassembled, clear the person elements totally and reassemble the diverter.
If the diverter is severely broken or leaking excessively, it might have to be changed. It is suggested to contact an expert plumber for this job.
By following these upkeep and cleansing ideas, you possibly can hold your bathtub spout diverter in optimum situation and lengthen its lifespan.
How To Change A Bathtub Spout Diverter
A tub spout diverter is a small, however necessary a part of your bathtub. It’s liable for directing the stream of water from the tap to the showerhead. In case your diverter isn’t working correctly, you could not be capable to use your bathe. Changing a tub spout diverter is a comparatively easy job that may be accomplished in a couple of minutes.
To exchange a tub spout diverter, you’ll need the next instruments:
- Adjustable wrench
- Pliers
- Screwdriver
- Substitute diverter
Upon getting gathered your instruments, comply with these steps:
- Flip off the water provide to the tub.
- Take away the previous diverter. To do that, use the adjustable wrench to loosen the nut that holds the diverter in place. As soon as the nut is unfastened, you need to use the pliers to drag the diverter out of the spout.
- Apply a small quantity of plumber’s putty to the threads of the brand new diverter. This can assist to create a watertight seal.
- Screw the brand new diverter into the spout. Tighten the nut till it’s cosy, however don’t overtighten it.
- Activate the water provide to the tub and verify for leaks. If there are any leaks, tighten the nut additional.
Individuals Additionally Ask
How do I do know if my bathtub spout diverter is damaged?
There are just a few indicators that your bathtub spout diverter could also be damaged. These embody:
- Water leaking from the spout when the bathe is on
- Issue switching between the spout and showerhead
- A unfastened or wobbly diverter
Can I change a tub spout diverter myself?
Sure, you possibly can change a tub spout diverter your self. The method is comparatively easy and could be accomplished in a couple of minutes. Nevertheless, if you’re not snug working with plumbing, you could need to rent a plumber to do the job for you.
How a lot does it price to switch a tub spout diverter?
The price of changing a tub spout diverter will fluctuate relying on the kind of diverter you select and the price of labor in your space. Nevertheless, you possibly can count on to pay between $20 and $50 for the diverter and $50 to $100 for labor.
