Changing a two-handle bathtub faucet is just not as troublesome as it could appear. With just a few easy instruments and slightly little bit of endurance, you possibly can have your new faucet put in very quickly.
Step one is to show off the water provide to the tub. That is normally achieved by turning off the valves situated beneath the sink. As soon as the water is turned off, you possibly can take away the outdated faucet by unscrewing the nuts that maintain it in place. Watch out to not injury the plumbing when you find yourself doing this.
As soon as the outdated faucet is eliminated, you possibly can set up the brand new one. Begin by inserting the brand new faucet within the gap within the bathtub. Then, screw on the nuts that maintain it in place. Make sure to tighten the nuts securely, however don’t overtighten them. Lastly, activate the water provide and test for leaks. If there are any leaks, tighten the nuts till the leaks cease.
Collect Obligatory Instruments and Supplies
Changing a two-handle bathtub faucet requires just a few important instruments and supplies to make sure a easy and profitable set up. This is a complete checklist of what you may want:
Instruments
- Adjustable wrench or spanner
- Phillips head screwdriver
- Flat head screwdriver
- Plumbers putty or Teflon tape
- Bucket or bowl
- Rags or towels
Supplies
| Part | Amount |
|---|---|
| New two-handle bathtub faucet | 1 |
| Faucet handles | 2 |
| Faucet aerators (elective) | 2 |
| Pipe dope or thread sealant | As wanted |
Moreover, chances are you’ll wish to take into account bringing a flashlight for higher visibility beneath the sink and a pair of labor gloves for defense.
Flip Off Water
Earlier than you start engaged on the tap, it is necessary to show off the water provide. This may stop water from spraying out of the tap once you take away the handles and cartridge. To show off the water provide, find the shut-off valves beneath the sink. The valves will usually be situated on the base of the tap, the place the water traces connect with the tap. Flip the valves clockwise to show off the water provide.
If there are not any shut-off valves beneath the sink, you will want to show off the water provide to your entire home. To do that, find the principle water shut-off valve, which is normally situated close to the entrance of the home, within the basement, or in a utility closet. Flip the valve clockwise to show off the water provide.
Ideas for Turning Off the Water
Listed here are just a few ideas for turning off the water provide:
- Just remember to have a wrench or pliers available to show the shut-off valves.
- If the shut-off valves are troublesome to show, you possibly can strive utilizing a pair of pliers to get a greater grip.
- In case you are unable to show off the water provide, it’s best to name a plumber for help.
| Device | Objective |
| Wrench or pliers | To show the shut-off valves |
Take away Aerators and Handles
Eradicating Aerators
Begin by unscrewing the aerator from the tap utilizing a wrench. If the aerator is caught, you should use a pair of pliers to softly loosen it.
As soon as the aerator is eliminated, it is possible for you to to see the cartridge. The cartridge is held in place by a screw, which you will want to take away utilizing a screwdriver.
As soon as the screw is eliminated, it is possible for you to to raise the cartridge out of the tap. Watch out to not lose the washer that’s situated behind the cartridge.
Eradicating Handles
To take away the handles, you will want to find the set screws which might be holding them in place. The set screws are normally situated on the underside of the handles.
After you have situated the set screws, you will want to loosen them utilizing a screwdriver. Watch out to not over-tighten the set screws, as this could injury the handles.
As soon as the set screws are loosened, it is possible for you to to tug the handles off the tap.
| Device | Description |
|---|---|
| Wrench | Used to unscrew the aerator. |
| Screwdriver | Used to take away the cartridge screw and set screws. |
| Pliers | Used to loosen a caught aerator. |
| Washer | Positioned behind the cartridge, it should not be misplaced. |
| Set screws | Maintain the handles in place. |
Disconnect Provide Strains
As soon as the handles and trim are eliminated, you will want to disconnect the availability traces. These are the versatile hoses that join the tap to the water provide pipes. Use an adjustable wrench to loosen the nuts that join the hoses to the tap.
Watch out to not overtighten the nuts, as you possibly can injury the hoses. As soon as the nuts are unfastened, you possibly can rigorously pull the hoses off the tap.
If the hoses are outdated or broken, chances are you’ll want to interchange them. To do that, lower the outdated hoses off the tap and the availability pipes. Then, connect the brand new hoses to the tap and the availability pipes utilizing the nuts that got here with the brand new hoses.
As soon as the availability traces are disconnected, you possibly can take away the outdated faucet from the sink or tub.
| Ideas |
|---|
| In case you are having bother disconnecting the availability traces, you should use a pair of pliers that will help you loosen the nuts. |
| Watch out to not injury the availability traces when you find yourself disconnecting them. |
| In case you are changing the availability traces, make it possible for they’re the proper size and that they’re rated for the water strain in your house. |
Take away Faucet Base
After eradicating the handles and cartridge, now you can take away the tap base. Place a bucket or towel beneath the tap to catch any water that will leak out.
Utilizing an adjustable wrench, loosen the nuts which might be holding the tap base in place. Watch out to not overtighten the nuts, as this could injury the tap.
As soon as the nuts are unfastened, you possibly can gently pull the tap base off of the bathtub deck.
If the tap base is caught, chances are you’ll want to make use of a rubber mallet to softly faucet it unfastened. Watch out to not hit the tap too laborious, as this could injury it.
As soon as the tap base is eliminated, now you can entry the plumbing connections.
Ideas for Eradicating the Faucet Base
| Ideas | Particulars |
|---|---|
| Use a bucket or towel to catch any water that will leak out | This may assist to stop water from damaging your flooring or carpet. |
| Watch out to not overtighten the nuts | Overtightening the nuts can injury the tap. |
| If the tap base is caught, use a rubber mallet to softly faucet it unfastened | Watch out to not hit the tap too laborious, as this could injury it. |
Clear Mounting Floor
Earlier than you start putting in the brand new faucet, it is necessary to totally clear the mounting floor. This may assist to make sure that the brand new faucet is put in securely and that there are not any leaks. Listed here are the steps to wash the mounting floor:
-
Take away any outdated caulk or sealant from across the outdated faucet. You need to use a utility knife or a razor blade to rigorously scrape away the caulk.
-
Clear the floor with a degreaser. This may assist to take away any grime, grime, or oil that might stop the brand new faucet from bonding correctly.
-
Rinse the floor with clear water and permit it to dry utterly.
| Tip | Description |
|---|---|
| Use a scrub brush to wash the floor totally. | This may assist to take away any cussed grime or grime. |
| Enable the floor to dry utterly earlier than putting in the brand new faucet. | This may assist to make sure that the brand new faucet is put in securely. |
Apply Plumber’s Putty and Set up Base
Step 7: Apply Plumber’s Putty and Set up Base
7.1: Take away the outdated plumber’s putty from the bottom of the brand new faucet utilizing a putty knife or scraper. Clear the realm totally with rubbing alcohol and permit it to dry.
7.2: Roll out a rope of plumber’s putty about 1/4 inch thick and 6 inches lengthy. Place the putty across the base of the tap, leaving a small gap within the heart for the water provide traces.
7.3: Flip the tap the wrong way up and place it over the mounting holes within the bathtub. Ensure that the putty is evenly distributed across the base and filling any gaps.
7.4: Place the mounting bolts by the holes within the faucet and into the tub. Tighten the nuts by hand till comfortable.
7.5: Flip the tap right-side up and manually tighten the mounting nuts additional. Keep away from overtightening, as this could injury the tap or bathtub.
7.6: Use a stage to make sure the tap is stage. Modify the mounting nuts as needed.
Set up Handles
1. Place the handles on the stems.
2. Apply a small quantity of plumbers grease to the threads of the deal with screws.
3. Insert the deal with screws into the handles and tighten them till they’re comfortable.
4. Use a wrench to tighten the packing nuts on every deal with.
5. Activate the water and test for leaks. If there’s a leak, tighten the packing nuts till the leak stops.
6. Set up the aerators on every deal with.
7. Activate the water and test for leaks. If there’s a leak, tighten the aerators till the leak stops.
8. Examine the operation of the tap. The handles ought to flip easily and the water ought to move evenly from the aerators. If the tap doesn’t function correctly, test the next:
| Potential Downside | Answer |
|---|---|
| The handles are stiff | Loosen the packing nuts on the handles |
| The water doesn’t move evenly from the aerators | Clear the aerators |
| The tap is leaking | Tighten the packing nuts on the handles or aerators |
Join Provide Strains
9. **Join Provide Strains to Faucet:**
a. Wrap plumber’s tape clockwise across the threaded finish of the cold and hot provide traces. Tighten them by hand onto the corresponding faucet inlets marked “H” and “C.”
b. **Use a Basin Wrench to Safe:**
| Tip | Profit |
|---|---|
| Insert a basin wrench into the opening within the faucet physique. | Permits entry to the nuts beneath the tap. |
| Tighten the nuts till they’re comfortable, however keep away from overtightening. | Prevents leaks and ensures a safe connection. |
c. **Examine Connections:**
Activate the water provide and test for leaks on the faucet inlets and provide line connections. If any leaks happen, tighten the connections additional as wanted.
Flip On Water and Examine for Leaks
As soon as the outdated faucet is eliminated, it is essential to activate the water provide to check for any potential leaks earlier than putting in the brand new one. Observe these steps to make sure a watertight seal:
- Open each the cold and hot water valves situated beneath the sink.
- Run each handles to permit water to move by the pipes.
- Examine the bottom of the tap, the availability traces, and another connections for any indicators of water leakage.
- In case you encounter any leaks, tighten the connections additional utilizing a wrench or pliers.
- As soon as the leaks have been addressed, flip off each water valves once more.
- Proceed with the set up of the brand new faucet, taking additional care to safe all connections.
- As soon as the brand new faucet is absolutely put in, activate the water valves once more and test for any remaining leaks.
- If all connections are safe and there are not any leaks, proceed to the following step of testing the performance of the tap.
- In case you encounter any persistent leaks that can’t be resolved, seek the advice of a licensed plumber for skilled help.
| Troubleshooting Leaks | |
|---|---|
| Leak at faucet base | Tighten the locknut beneath the tap. |
| Leak at provide line connections | Use a wrench to tighten the nuts connecting the availability traces to the tap. |
| Leak at pop-up drain | Examine the drain stopper meeting and exchange any worn-out parts. |
How To Change A Two Deal with Bathtub Faucet
Changing a two-handle bathtub faucet is a comparatively easy job that may be accomplished in just a few hours. With the fitting instruments and supplies, it can save you your self the price of hiring a plumber.
Instruments and Supplies
• Adjustable wrench
• Basin wrench
• Plumber’s putty
• Teflon tape
• New bathtub faucet
• Utility knife
Directions
- Flip off the water provide to the tub. There ought to be two shut-off valves situated beneath the sink. Flip the handles clockwise to shut them.
- Open the tub faucet to launch any remaining water strain.
- Use the adjustable wrench to loosen the nuts that maintain the handles in place. Take away the handles.
- Use the basin wrench to loosen the nuts that maintain the tap physique in place. Take away the tap physique.
- Apply a bead of plumber’s putty to the bottom of the brand new faucet physique. Wrap the threads of the tap physique with Teflon tape.
- Set up the brand new faucet physique and tighten the nuts with the basin wrench.
- Set up the handles and tighten the nuts with the adjustable wrench.
- Activate the water provide to the tub and test for leaks. If there are any leaks, tighten the nuts additional.
Individuals Additionally Ask About How To Change A Two Deal with Bathtub Faucet
How a lot does it price to interchange a tub faucet?
The fee to interchange a tub faucet can fluctuate relying on the kind of faucet you select and the complexity of the set up. Nonetheless, you possibly can anticipate to pay between $100 and $500 for the tap and set up.
Can I exchange a tub faucet myself?
Sure, you possibly can exchange a tub faucet your self with the fitting instruments and supplies. Nonetheless, in case you are not snug working with plumbing, it’s best to rent a plumber.
What’s the greatest sort of bath faucet to purchase?
One of the best sort of bath faucet for you’ll rely in your wants and preferences. Some standard forms of bathtub taps embrace:
- Two-handle taps
- Single-handle taps
- Thermostatic taps
- Sensor taps
