Changing the belt in your Whirlpool dryer is a comparatively easy job that may be accomplished in below an hour. Nevertheless, earlier than you start, you will need to collect the entire mandatory instruments and supplies. You will have a brand new dryer belt, a screwdriver, and a pair of pliers. Moreover, it’s useful to have a flashlight available that can assist you see into the dryer cupboard.
Upon getting gathered your instruments and supplies, you possibly can start by unplugging the dryer from the ability outlet. Subsequent, open the dryer door and take away the screws that maintain the entrance panel in place. As soon as the screws are eliminated, you possibly can fastidiously raise the entrance panel off of the dryer cupboard. Make sure you assist the entrance panel with one hand when you take away the screws with the opposite hand.
With the entrance panel eliminated, you should have entry to the dryer belt. The belt is often situated across the drum and the motor pulley. To take away the belt, merely slip it off of the pulleys. As soon as the belt is eliminated, you possibly can set up the brand new belt by slipping it onto the pulleys in the identical method that you simply eliminated the previous belt. Make sure you tighten the belt till it’s cosy, however don’t overtighten it.
Gathering Essential Instruments and Supplies
Earlier than embarking on the duty of changing the belt in your Whirlpool dryer, it’s essential to collect the required instruments and supplies to make sure a easy and environment friendly course of. Here’s a complete checklist of what you have to:
Instruments:
| Software | Objective |
|---|---|
| Phillips head screwdriver | Eradicating screws |
| Flat head screwdriver | Prying unfastened panels |
| Adjustable wrench or pliers | Gripping and loosening components |
| Flashlight | Illuminating hard-to-reach areas |
Supplies:
- Alternative dryer belt (Whirlpool-compatible)
- Dryer glides or rollers (if wanted)
- Lint filter
- Clear material or rags
- Security glasses (elective)
Be aware: Be certain that the substitute belt matches the mannequin and specs of your Whirlpool dryer to keep away from compatibility points.
Unplugging the Dryer
To make sure your security and forestall any electrical accidents, the primary essential step in changing the belt in your Whirlpool dryer is to unplug it from its energy supply.
1. Find the Energy Twine
Discover {the electrical} outlet the place the dryer is plugged in. Observe the ability twine to the again of the dryer to make sure that it’s securely related.
2. Safely Take away the Twine
Grasp the plug firmly by the physique, not by the twine. Pull the plug straight out of {the electrical} outlet with a delicate however agency movement. Don’t yank or pull on the twine, as this might injury the outlet or the ability twine itself.
3. Safe the Twine
As soon as the ability twine is disconnected, set it apart in a protected place the place it won’t turn out to be a tripping hazard or trigger any entanglement when you work on repairing the dryer.
| Security Suggestions |
|---|
| – Be certain that your palms are dry earlier than dealing with the ability twine. |
| – If you’re uncertain about find out how to safely unplug the dryer, seek the advice of a professional electrician. |
| – Don’t try and function the dryer whereas it’s unplugged, as this might pose a security hazard. |
Eradicating the Rear Panel
To take away the rear panel, comply with these detailed steps:
1. Unplug the dryer: Unplug the ability twine from {the electrical} outlet to make sure security.
2. Find the screws: Examine the rear panel for 2 screws on the backside corners.
3. Take away the screws: Utilizing a screwdriver, fastidiously take away the 2 screws. The screws could also be recessed, so you should definitely use the suitable screwdriver kind.
**Detailed Process for Eradicating Recessed Screws:**
| Steps | Particulars |
|---|---|
| Find the recesses: | Establish the small recesses across the screw heads. |
| Insert the screwdriver: | Align the screwdriver tip with one of many recesses. |
| Apply strain: | Push down firmly on the screwdriver and switch it counterclockwise to unscrew the screw. |
| Take away the screw: | As soon as the screw is unfastened, pull it out from the panel. |
4. Raise the panel: As soon as the screws are eliminated, gently raise the rear panel upwards by holding its edges.
Finding the Belt
To find the belt in your Whirlpool dryer, comply with these steps:
1. Unplug the dryer from the ability outlet.
Security first! All the time unplug the dryer earlier than engaged on it.
2. Take away the entrance panel of the dryer.
Find the screws that maintain the entrance panel in place, often on the high or backside of the panel. Take away the screws and punctiliously raise the entrance panel off the dryer.
3. Find the drum.
The drum is the massive, cylindrical a part of the dryer that holds the garments. It’s situated within the middle of the dryer.
4. Examine the belt.
The belt is a thick, rubber band that wraps across the drum and the motor pulley. It’s chargeable for transmitting energy from the motor to the drum. The motor pulley hooked up to the drive motor often situated again behind the drum and the loafer pulley is chargeable for tensioning the belt. Examine the belt for any indicators of wear and tear or injury. If the belt is cracked, frayed, or damaged, it would must be changed.
| Indicators of Belt Injury |
|---|
| Cracks |
| Fraying |
| Breaks |
Inspecting the Pulley
Checking the Pulley for Put on and Injury
As soon as the previous belt is eliminated, fastidiously examine the pulleys for any indicators of wear and tear or injury. Search for cracks, dents, or extreme put on on the grooves. Any abnormalities within the pulley’s floor can have an effect on the belt’s efficiency and lifespan.
Cleansing the Pulley Floor
Use a clear material or compressed air to take away any particles or residue from the pulley floor. This ensures a easy and clear floor for the brand new belt to grip correctly.
Inspecting the Pulley’s Alignment
Test if the pulley is aligned appropriately. Misaligned pulleys could cause the belt to slide or come off, resulting in additional issues. Use a straightedge or laser degree to find out if the pulley is perpendicular to the dryer’s body.
Inspecting the Pulley Grooves
Take note of the situation of the pulley grooves. If the grooves are worn out or broken, the belt might not seat correctly, leading to diminished grip and effectivity. Test for any overseas objects or obstructions within the grooves that would hinder belt motion.
Reinstalling the Pulley
If the pulley must be changed, set up the brand new pulley fastidiously. Guarantee it’s correctly aligned and tightened based on the producer’s specs. Failure to safe the pulley appropriately could cause vibrations and different points throughout operation.
Eradicating the Worn Belt
Step 1: Unplug the Dryer
Disconnect the dryer from its energy supply by unplugging it from the wall outlet. By no means try any repairs on an energized dryer.
Step 2: Transfer the Dryer Out
Fastidiously pull the dryer ahead to create sufficient workspace behind it. This can present simpler entry to the again panel, the place the belt is situated.
Step 3: Take away the Again Panel
Find the screws holding the again panel in place. Utilizing a screwdriver, take away these screws and punctiliously raise off the again panel, setting it apart.
Step 4: Find the Belt
The drive belt is often located across the motor pulley and the drum pulley. It might be made from rubber or nylon and is commonly black in coloration.
Step 5: Take away the Outdated Belt
Seize the previous belt together with your palms and gently pull it off the motor pulley. Then, slide it off the drum pulley. Watch out to not injury the pulleys or the belt throughout this course of.
Step 6: Examine the Pulleys and Loafer Arm
With the belt eliminated, take a better have a look at the motor pulley, drum pulley, and loafer arm. Test for any indicators of wear and tear, injury, or misalignment. Should you discover any abnormalities, exchange the affected parts earlier than putting in the brand new belt to make sure optimum efficiency.
Part Inspection Desk:
| Part | Test for |
|---|---|
| Motor Pulley |
|
| Drum Pulley |
|
| Loafer Arm |
|
Putting in the New Belt
With the loafer pulley screw loosened, slip the brand new belt across the drum. Make sure the belt is correctly seated within the pulley grooves. Subsequent, rotate the drum by hand to make sure the belt is aligned appropriately.
Find the motor pulley and place the belt round it. Once more, make sure the belt is correctly seated within the pulley grooves.
Tighten the loafer pulley screw to rigidity the belt. The belt needs to be tight sufficient to forestall slipping however not so tight that it places undue stress on the motor or different parts. rule of thumb is to tighten the belt till you possibly can deflect it about 1/2 inch with average strain.
Reinstall the entrance panel of the dryer and safe it with the screws. Reconnect {the electrical} twine and switch the dryer again on.
Run the dryer for a couple of minutes to check the brand new belt. Hear for any uncommon noises or vibrations which will point out the belt shouldn’t be put in appropriately.
If the dryer is working easily and quietly, the belt has been efficiently put in.
| Troubleshooting Suggestions for Belt Set up |
|---|
|
Tightening the Belt
As soon as the brand new belt is in place, it have to be tightened to the right rigidity. That is necessary to forestall the belt from slipping or breaking. To tighten the belt, use the next steps:
1. Find the tensioner pulley.
The tensioner pulley is often situated on the motor or loafer pulley bracket. It has a spring or lever that may be adjusted to vary the stress on the belt.
2. Loosen the tensioner pulley.
Use a wrench or screwdriver to loosen the tensioner pulley. This can mean you can transfer the pulley and modify the stress on the belt.
3. Transfer the tensioner pulley.
Transfer the tensioner pulley to extend or lower the stress on the belt. The belt needs to be tight sufficient to forestall slipping, however not so tight that it causes the motor to overheat.
4. Tighten the tensioner pulley.
As soon as the belt is on the right rigidity, tighten the tensioner pulley. This can lock the pulley in place and maintain the belt on the right rigidity.
Here’s a desk with some ideas for tightening the belt on a Whirlpool dryer:
| Tip |
|---|
| Use a wrench or screwdriver to loosen the tensioner pulley. |
| Transfer the tensioner pulley to extend or lower the stress on the belt. |
| Tighten the tensioner pulley as soon as the belt is on the right rigidity. |
Changing the Rear Panel
Step 1: Unplug the dryer. Security first! All the time unplug the dryer earlier than performing any upkeep or repairs.
Step 2: Take away the 2 screws on the backside of the rear panel. These screws maintain the panel in place.
Step 3: Pull the rear panel away from the dryer. It ought to come off simply.
Step 4: Find the belt. The belt is a big rubber band that wraps across the drive pulley and the drum pulley.
Step 5: Take away the previous belt. To do that, merely slip it off the pulleys.
Step 6: Set up the brand new belt. Wrap the brand new belt across the drive pulley first, then across the drum pulley.
Step 7: Be certain that the belt is correctly tensioned. The belt needs to be cosy, however not too tight. If it is too unfastened, it would slip and trigger the dryer to overheat. If it is too tight, it would put pointless stress on the motor.
Step 8: Reattach the rear panel. Line up the panel with the dryer and push it again into place. Safe it with the 2 screws you eliminated earlier.
Step 9: Reconnect the dryer to the ability outlet and run a take a look at cycle. If the dryer operates usually, you have efficiently changed the belt.
Testing the Dryer
10. **Manually turning the drum**: With the dryer unplugged, manually flip the drum to examine for resistance. If the drum doesn’t spin freely or there’s a grinding noise, it might point out a damaged belt or different mechanical points.
-
Security First: All the time unplug the dryer from the ability provide earlier than performing any repairs.
-
Establish the Mannequin: Decide the mannequin variety of your Whirlpool dryer by checking the sticker situated on the again of the unit. This data will enable you to discover the right substitute belt.
-
Find the Belt: Open the dryer door and find the drum behind the equipment. The belt is often wrapped across the drum and the motor pulley.
-
Test for Injury: Examine the belt for any seen injury, comparable to cracks, fraying, or lacking sections. If the belt is broken, it would must be changed.
-
Take a look at the Rigidity: Seize the belt and pull it in direction of you to examine its rigidity. It needs to be cosy however not too tight or too unfastened. If the belt is just too unfastened, it could slip off throughout operation, whereas a belt that’s too tight can put extreme pressure on the motor.
Drum Assist Rollers
-
Examine the Rollers: Whereas the belt is eliminated, examine the drum assist rollers for any put on or injury. These rollers assist assist the drum and guarantee easy rotation. If the rollers are broken, they need to get replaced.
-
Clear the Rollers: Use a vacuum cleaner or a delicate brush to wash any mud or particles from the rollers and their bearings. This can assist forestall future put on and tear.
Methods to Exchange a Belt on a Whirlpool Dryer
Changing the belt on a Whirlpool dryer is a comparatively easy job that may be accomplished in about half-hour. The next steps will information you thru the method:
- Unplug the dryer and disconnect the gasoline line. In case your dryer is gas-powered, you should definitely flip off the gasoline provide earlier than disconnecting the road.
- Take away the entrance panel. To take away the entrance panel, first take away the 2 screws which are situated on the backside of the panel. Then, raise the panel up and off of the dryer.
- Find the belt. The belt is situated across the drum and the drive pulley.
- Take away the belt. To take away the belt, first loosen the tensioner pulley. To do that, insert a screwdriver into the slot on the tensioner pulley and switch it counterclockwise. As soon as the belt is unfastened, you possibly can take away it from the drum and the drive pulley.
- Set up the brand new belt. To put in the brand new belt, first place it across the drum. Then, place the belt across the drive pulley. Lastly, tighten the tensioner pulley by turning it clockwise.
- Reassemble the dryer. To reassemble the dryer, first exchange the entrance panel. Then, reconnect the gasoline line and plug within the dryer.
Folks Additionally Ask
How usually ought to I exchange the belt on my Whirlpool dryer?
It’s best to exchange the belt in your Whirlpool dryer each 5-7 years, or extra usually in the event you use your dryer often.
What are the indicators that my Whirlpool dryer belt must be changed?
There are a couple of indicators that your Whirlpool dryer belt must be changed, together with:
- The dryer is making a squealing or squeaking noise.
- The dryer shouldn’t be drying garments as effectively because it used to.
- The dryer is taking longer to dry garments.
- The dryer is overheating.
Can I exchange the belt on my Whirlpool dryer myself?
Sure, you possibly can exchange the belt in your Whirlpool dryer your self. Nevertheless, you will need to comply with the steps fastidiously to keep away from damaging your dryer.
